Appliance Type: Dishwasher

bosch dishwasher model she6at05ucx/o5
error cod e64
we replaced the control board to no avail
need some assitance please we belieive it could be heating system , also
how do you get this dishwasher into test mode

intermittently The dishwasher has water in the bottom one time it pumps out fine. Next time Not. There is Little ball in sump area what is it for

Frigidaire dishwasher Model FDB51OLCS3 The water will not go all the way to the top of the tube to flow into the upper rack wash arm so it will turn . If you take the ball out of the sump the water will then flow to the upper wash arm but the arm still will not turn . Do not see anything in the sump blocking the water flow.

Frigidaire dishwasher bottom arm works great upper arm does not turn because the water does not go all the way to the top of the tube that runs up the side and to the top of the dishwasher and then shoots down to the upper wash arm . I have added more water and that does not help . If I stop the washer and restart it in a few seconds the water will start then flowing strong to the upper rack threw the tube . When this happens the lower arm them gets no water to it . I did take the motor out and found some glass in the motor wheel , removed the glass and reinstalled the motor but that did not help the problem. The motor runs and seems to be running fine could the motor not be running as fast as it should and be the problem ? Only thing I can think is maybe a motor problem , the motor does seem to be running ok .

My Frigidaire Professional FPHD2491KF buttons don’t work. Well only two light up when I press them. The start button does not work so I can’t run the machine. Would that be a console assembly problem or a pc board problem? How would I find out which one needs to be replaced as I have searched many forums and websites indicating that it can be either the PC board or the Consol assembly (panel where you press buttons) Thanks!

How do I test soap dispenser using diagnostic codes to activate solenoid.

Is there a video for Dissasembly of door and testing of part 00645208 to make sure the solenoid is working and the control board is sending correct voltage?

What is voltage used to activate solenoid.

Should I remove entire door?

Removing dispenser is tricky is there a better way?

The wash program selector is stuck on “Rinse” and will not move.

I’m hoping one of the techs there can help me figure out what part I need to replace. I’ve checked the line and the pump for any debris but didn’t see anything. Just sounds like the pump isn’t actually working correctly. Is it more than one assembly I’ll need to replace? A video would be great as well if you can find one for me.

Hi, my dishwasher randomly came on with a blinking clean light. I watched your informative video on how to reset the codes on other whirlpool dishwashers, mine however doest have the same button setup, and am curious if you know the button combination to reset mine. Ive inspected to element and put a multimeter on it to read the ohms, this checks out as fine. any help would be much obliged.

-bill

Unit will only start in diagnostic mode. When I first start diagnostic mode, all lights are green. The unit Will get a few minutes in to diagnostic mode and dies, no lights and the unit will not respond. It will only respond trying to run diagnostic mode, always get the same result, it dies and is unresponsive.

I checked to see if the chopper blade was jammed, it was not. I replaced the control board, that did not fix the issue.

Any ideas. Could it be the thermal fuse? Would diagnostic mode still try and work if the thermal fuse is bad?

I tried working through the service manual attached to the inside of the kickplate but there wasn’t anything in the troubleshooting that referenced what to look for when the unit died during the diagnostic mode.

I assume that once the unit got to somewhere in diagnostic mode that wasn’t working properly it shut down…

Any ideas or feedback would be appreciated.

I saw the videos on clearing the chopper and sump area, and I checked the pump as well. I removed some debris thinking I’d solved it, but same thing happened on next load. Not sure where to go from here.