0 votes
5k views

Ran through diagnostic mode all major components seem to check out and service manual with that unit does not have a F 36 code. The unit seems to come on normally but as soon as you hit a function it flashes the Error and shuts off. Can you guys give me an input not just the manual it doesn’t seem to have an answere.

0 votes
5k views

The dishwasher start/cancel button will press bit does not rest or start. I flipped the breaker for 10 minutes and it continued to do the same thing. I set it on 1 hr delay thinking maybe it would start. It locked up and no cycle buttons, delay options, or extras like heated dry will change now. I flipped the breaker and left it off the rest of the day. Last night (about 5 hrs later) it’s still flashing at me. I used it Saturday with no problems. Sunday it started with this mess. My 4 yr old did spill water on the counter and into the floor but the dishwasher is completely under the lip of the countertop. I doubt that enough water may have gotten on it but if it did then why did the other buttons work before flipping the breaker. The dishwasher is about 2.5-3 yrs. I use it 3-4 times per week. We’ve checked the filters and the ensured that the racks were in properly.

0 votes
4k views

only the heavy wash and high temp dry buttons work or will light up and when you push the start cancel button nothing happens. When you close the door the display lights up but the wash light does not come on and nothing happens. after a minute or two the display shuts off. Ocassionaly it will work bit only on heavy wash and high temp dry.
I replaced the control panel and the same thing happens. Your video showed the same symptoms and was resolved by changing the control panel. I am hoping I do not have to change the control board as that is another $100 + part.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
4k views
e21

so the unit is getting an e 21 error. i put it into the diagnostic test mode and it will not go past s01
please advise

  • Guest asked 5 years ago
  • last active 5 years ago
-1 votes
4k views

Need parts or Repair Help on a Viking 100 Series 24″ Custom Panel Built-in Dishwasher FDW100

0 votes
4k views

KitchenAid dishwasher model KUDS30IXBL8 do you have parts list ?

  • Guest asked 9 years ago
  • last active 9 years ago
1 vote
4k views

Looking for some info on this.

  • dwoods asked 5 years ago
  • last active 5 years ago
1 vote
4k views

It will not respond to any command and will not clear and this code is NOT in the tech sheet in the unit. What does it mean? Is it indicating a stuck key pad?

  • Pancakes asked 6 years ago
  • last active 6 years ago
0 votes
4k views

THANKS FOR YOUR HELP on our Frigidaire dishwasher. WE ALREADY FORKED OUT $120 AND REPLACE THE CONTROL BOARD AND THE ERROR CODE IS STILL FLASHING. I GUESS WE NEED TO WORK ON THE TOUCH PANEL OR CONSOLE, HUH? That should do it, right? Is there a video showing how to do this?

CHRIS HIGGINBOTHAM

  • CHRIS HIGGINBOTHAM asked 9 years ago
  • last active 9 years ago
1 vote
4k views

The dishwasher overfills and goes into the drain pan causing the E15 error. I cannot find a float switch that regulates how much water fills the dishwasher. What do I change to cause it to fill normally?

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
4k views

I have some infomation about that error cod,the problem coud be with the electronic control board or could be the heating element. I want to know wich one could be the problem.  The costumers told me just to replace the heating element. Hope is going to fix the problem.  Could you please post a video how to replace the heating element for that dishwasher.  Some, advice how to make easy to replace that thanks so much for the help. Tomorrow i have that service at 9am can you post the video as soon as posible thanks alot.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

My dishwater is leaking water from somewhere.

0 votes
4k views

I have a Samsung dishwasher that displays a SE or 5E fault. That fault I believe is associated with it not draining but it drains just fine. Every time the error is there the water is pumped out and I can always force it to drain by canceling the cycle. Please let me know if anyone else has had this issue.
Thanks,

0 votes
4k views

This dishwasher as it tries to drain flashes E1

0 votes
4k views

Hi Folks,
This unit is showing the following code: Under the cycle mode there are 3 lights blinking, the first two and the fourth i.e. Smart Auto – Normal – Skip –Delicate! Also, while the door is open the pump is on and pumping out. According to the troubling shooting guide this all relates to high temperature water entering the unit. Although it says nothing about the unit working with the door open. Can someone please point me in the correct direction?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
4k views

f6-e4
f6-e3
f9-e1
f5-e1

any help on these codes?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
4k views
  • Phyllis asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Kenmore Elite dishwasher made by Whirlpool that will not drain properly every time. Will work 1 or 2 cycles then at the end of the 3rd cycle will leave about an inch of water in bottom of the dishwasher. Everytime I drain the dishwasher through the cancel cycle it does just fine.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

My dishwasher will not start. The lights light up when I choose different functions but it won’t actually start when I press Start. I tried the reset by pushing the High Temp Scrub and Energy Save Dry buttons alternating five times each and the unit will go through the reset. It also drains when I press cancel after resetting. I am not sure how to proceed.

  • Ryen Mullen asked 9 years ago
  • last active 9 years ago
1 vote
3k views

I CLOSE THE DOOR ON CUSTOMERS D/W AND BREAKER TRIPS WITH NO DRAMA RESET DISPLAY LIGHT AS NORMAL CLOSE DOOR BREAKER TRIPS IM NOT A NEWBIE BUT THIS PARTICULAR MODEL IS KIND OF COMPLICATED ANY HELP WOULD BE GREAT THANK YOU

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Leaking water.

0 votes
3k views

Not drying.

0 votes
3k views

Control panel LEDS are flashin On, , Off, On. This happens right after the unit fills, then drains and refills. I have changed the case sensor and water valve. I am leaning to a new flow meter before I take this unit out. Any help would be greatly appreciated.

0 votes
3k views

The dishwasher has power. The Hi-scrub light is on. No switches will activate any function. Nothing comes on when the door is closed.

  • smcanall asked 6 years ago
  • last active 6 years ago
0 votes
3k views

The dishes do not seem to be getting dried at the end like they used to, and also not getting as clean. Thought maybe it was the control panel but it seems fine. Water pressure is good, and I cleared the spray arms of any debris and cleaned them well before putting them back in. Seems to be cycling correctly. Wasn’t sure what to check next.

0 votes
3k views

my Bosch dishwasher is leaking water.

0 votes
3k views

Hello, I just replaced the defective touch panel. I need to know how to clear the error code on this model. Maytag dishwasher MDB4949SDZ. Thank you, Shawn

0 votes
3k views

I have no lights on display and no power to control board.

  • CHA020118 asked 6 years ago
  • last active 6 years ago
0 votes
3k views

Soap does not dispense, Poor drying.

0 votes
3k views

The wash program selector is stuck on “Rinse” and will not move.

  • Ed asked 9 years ago
  • last active 9 years ago
Showing 31 - 60 of 885 results