1 vote
1k views

Still no start. No cycle/ No cancel/drain either. There is power to door switch but not to machine. Can’t find any info for this model online.

  • appliance7 asked 5 years ago
  • last active 5 years ago
1 vote
3k views

No power to dish machine. I tried to communicate with different individuals on this unit. One advised me to replace control panel, which I did. Same result. A second person told me it was the main circuit board, which I replaced. Again, same result. Just saw a video on noise filter. Told me to check fuse under epoxy but my filter did not have a fuse. Considering what I have paid for parts I should have bought a new dishwasher but I’m committed to fixing this thing now. Also the cord for the doors that attach to springs have snapped off if you can give me part numbers on the cords I would appreciate it ——- greatly!

  • Jpnagle611 asked 5 years ago
  • last active 5 years ago
1 vote
2k views

This dishwasher has a new sump so it came with a new grommet. The diverter motor is leaking when the pump starts spraying. Any way of sealing this up? Or would it need a new diverter motor?

  • RBair asked 5 years ago
  • last active 5 years ago
1 vote
1k views

No power on display. Checked power coming in at the bottom of dishwasher terminal and there is 120 volts coming in. I’m thinking it’s the board but I want to make sure since I can’t find any service manual for this model. Thanks.

1 vote
2k views

when you wash the dishes it gets to the rinse the unit just starts beeping and continues to beep? Have you heard of this problem and know what the the common problem for this unit is. There is a little water in the unit after the drawer is pulled out. Is this normal?

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
2k views

when it gets to the end to the end of the cycle the unit will still run. Evan over night

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
2k views

Fills but does not drain goes through cycle except for drain

  • Bbcl9268 asked 6 years ago
  • last active 6 years ago
1 vote
1k views

Three days ago, I heard a noise after the washer completed its cycle. Upon inspection, I’ve discovered, the square-shaped motor on the bottom of the machine is running non-stop. It will only stop when the machine is unplugged. All other operation seems fine: e.g., dishes are getting cleaned, water is draining and there are no funny noises while the machine operates. Further, there are no blinking lights.

I cannot find anything online, including your videos, which describe the symptoms I’m observing. My only guess is whatever controls the motor is causing the problem – a stuck relay, or a bad board… I’m stuck and need help.

Thanks in advance.

  • esurrett asked 5 years ago
  • last active 5 years ago
1 vote
1k views

The appliance is only run approximately every 2 weeks as there are only 2 of us seniors in the household. I made all the selections as normal and selected the start, closed the door immediately, and shortly afterward the light started flashing and the beeper comes on. I have canceled the program multiple times and re-selected different programs to see if made any difference, but the same results occurred once the door was shut. I have check all the filters to ensure they are clean. I do not have an electrical schematic to see if there are any other permissive interlocks that could be holding the start initiation sequence out.

  • Guest asked 4 years ago
  • last active 4 years ago
1 vote
2k views

The dishwasher appears to run well and fill and drain properly. I did notice that water was not hot during wash cycle. I could hear the spray arms rotating well. Is this dishwasher supposed to heat up the water. I need the manual or schematic for it. Thank you. I did check the filter screen and didn’t look that bad.

  • cato91891 asked 6 years ago
  • last active 6 years ago
1 vote
4k views

Looking for some info on this.

  • dwoods asked 5 years ago
  • last active 5 years ago
1 vote
3k views

Customer gave no details of when the dishwasher gives the code, only that it reads the code: nE.

  • dwoods asked 4 years ago
  • last active 4 years ago
1 vote
2k views

I need a service manual. I tried a service test holding power heavy and delicate and it displayed 15. My old manual only shows codes by less. Is it in flood mode? Maybe the sensor in the bottom? What does this sound like?

  • Pancakes asked 7 years ago
  • last active 7 years ago
1 vote
2k views

Tested element, reads good. Replaced control panel and main relay still no go? Tested heater connection on relay so means thermal fuse and wiring is fine, outlet a good 123v..? Goes through normal hour cycle but doesn’t dry..
Already asked question got French trouble shooting guide asking again

1 vote
4k views

It will not respond to any command and will not clear and this code is NOT in the tech sheet in the unit. What does it mean? Is it indicating a stuck key pad?

  • Pancakes asked 6 years ago
  • last active 6 years ago
1 vote
1k views

The customer showed me a video that sounded like the pump running with the door open. She said that it shows an error code often of 10 and last time it showed 30.
Where is the tech sheet hidden? I couldn’t find it behind the door panel or behind the toe plate.
I need a copy of it and the error codes and videos.

  • Pancakes asked 4 years ago
  • last active 4 years ago
0 votes
2k views

I am going out to check a kenmore dishwasher customer states its not draining. I would like to see a video on checking this thing out pls thanks

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Have 14 vdc at user interface

  • user asked 4 years ago
  • last active 4 years ago
0 votes
2k views

Hello
I’m working on whirlpool d.w, start light and cancel light flashing rapidity. I tried hard rest but nothing happened. I also tried putting into diagnose mode but not working either.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views
0 votes
2k views

I had this touch pad replaced on my dishwasher less than a year ago. Could this one be dead already? The repairman also replaced the control unit but it turns out it didn’t need replacing anyway.

I decided myself to replace the door latch because the old one was broken and the repairman last year threw out the handle part!! GRRRR! Some repairman! The latch is the new improved design anyway.

I checked the big fuse and it is good with power all the way to the control board.

Not sure what else can go bad on this model? I have a new touch pad panel coming but if that doesn’t fix it what is my next area to look at?

Thanks for any help.

  • Clay asked 10 years ago
  • last active 10 years ago
0 votes
2k views

intermittently The dishwasher has water in the bottom one time it pumps out fine. Next time Not. There is Little ball in sump area what is it for

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

There is a very small leak that sometimes gets into the drip pan underneath and sets off the leak detector. It is a very small amount of water and I cannot findmwhere it is coming from, as it doesn’t always leak.

There is a small chunk of the door seal missing on the side of the leak. It is about 2” from the bottom. This missing piece is about 1/8” of the lip and about 3/16” long. Could this be the source, even though I cannot find a visible water path.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
25k views

hi , i am an appliance repair man in canada, and i have a customer that has an 3C error mid cycle, i went there ran the machine for 10 minute nothing came up, tried to manually drain the machine drains fine, cleaned the filter, but dont know where to look for this error, nothing seem to be wrong with the machine.. please help

0 votes
3k views

Samsung dishwasher that is giving a 7E code. Can you tell me what this is and how to fix it, and hopefully a video of the repair

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

the only way to turn off the motor is by turning off the power

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views
0 votes
18k views

Dishwasher fills and runs for a while, then stops mid cycle with an E17 error.

0 votes
2k views

Quick rinse is blinking,cancel light is blinking,lock on is blinking. Is there a why to cancel and run normal wash cycles?

  • Guest asked 8 years ago
  • last active 8 years ago
Showing 31 - 60 of 885 results