I repaired the drain pump on my dishwasher. Now I can’t get it to start.
- Paul Bergstrom asked 10 years ago
- last active 10 years ago
hi , i am an appliance repair man in canada, and i have a customer that has an 3C error mid cycle, i went there ran the machine for 10 minute nothing came up, tried to manually drain the machine drains fine, cleaned the filter, but dont know where to look for this error, nothing seem to be wrong with the machine.. please help
- Guest asked 6 years ago
- last active 6 years ago
How can I winterize my dishwasher for my summer cottage. I drain all the water from the system and use the air compressor to finalize so no water is in the lines. RV antifreeze to the traps.
Can you assist? I saw many of your you tube videos for how tos but not on the dishwasher winterization
Thanks
- kathy mccarthy asked 10 years ago
- last active 10 years ago
Samsung dw 1E error code, model DW80F800UWS/AA, serial B009g9md604628d
This is supposed to be a high temp heating error. Had schematic for DMT800 series dishwasher with me. This wire diagram did not match the wire diagram on the main pcb cover on dw. Did not see thermistor listed on dw wire diagram on unit.
Heating element had 12 ohms, but no power going to it in quick wash cycle. Could not get it into diagnostic mode.
What should I be checking? I am guessing you need to pull the unit to get to components like LG brands?
- Ted Hood asked 9 years ago
- last active 8 years ago
Dishwasher fills and runs for a while, then stops mid cycle with an E17 error.
- Guest asked 6 years ago
- last active 6 years ago
Hi –
My kitchenaid dishwasher (3 years old) is leaking water under the right bottom side of the door. It is not a lot of water, and my first attempt to fix it was cleaning the seal, which had some small amount of scum on it. This fixed it temporarily, but a few days later the water leak was back. It is not a lot of water, and doesn’t happen during the rinse only cycle, apparently. Any ideas/thoughts on this would be very useful. It is a stainless steel kitchenaid dishwasher, similar to model KDTE104DSS.
Thanks!
Adam
- Adam asked 10 years ago
- last active 8 years ago
What does this part do? Does it recycle the water. I would like to know. Will it stop the dishwasher from turning the motor on if it doesn’t work?
- Guest asked 8 years ago
- last active 8 years ago
I own an appliance repair company in Texas. I have found the upper rack may disengage from the rails when the
customer pulls the upper rack out to load or unload the dishes
Wheel axle breaks and causes upper rack to fall when pulled out on many of the dishwashers.
Any suggestions would be greatly appreciated thanks in advance James.
- James Londen asked 9 years ago
- last active 8 years ago
Hi,
I need to replace my waterwall vane motor and have ordered the motor (part number DD31-00013B). I watched the video on how to remove the motion assembly and waterwall but I’m not sure how to remove the old motor and install the new one. Does the old motor drive pin just slide out and then just slide the new motor in or is there a seal i need to replace?
- Guest asked 7 years ago
- last active 7 years ago
The unit keeps getting a low water error and everything I could think of checks out: inlet valves, water pressure, fills with correct amount of water, board/panel is fine, cleared some minor debris from the pump, and checked that the float works. What am I missing?
- Harley Clark asked 9 years ago
- last active 8 years ago
My Samsung dishwasher is displaying a 4c error code.
- Don Kopecky asked 7 years ago
- last active 7 years ago
I have a GE dishwasher and the Vent Cover keeps “Popping Off” and the is Vent Leaking . Is there a fix for this issue ?
- Harley Clark asked 6 years ago
- last active 6 years ago
Pump motor constantly running giving error code i30 checked drain pump everything working fine
- Guest asked 7 years ago
- last active 7 years ago
Our dishwasher quit working and is flashing an ER code. How do we diagnose what it needs?
- Chris Higginbotham asked 9 years ago
- last active 9 years ago
Customer called with a Samsung dw model DMT400RHS, lights flashing on SMART AUTO and HEAVY.
Does anyone know what this code means?
- Gary Williams asked 9 years ago
- last active 9 years ago
The Smart Auto and Normal LED’s are flashing per the customer. I found the motor/pump locked up due to lack of use, unstuck impeller, unit running. Not sure what the flashing LED’s reference.
- Guest asked 10 years ago
- last active 8 years ago
I’m getting 7E error and grinding noises at certain points. It used to wash for a while, then stop with the 7E error. I checked that the water wall part that moves was attached properly and oriented correctly. Ultimately, I replaced the motor/sensor assembly. Now, when I start it, the water wall cycles back and forth, making a grinding sound when it gets all the way to the back (I think) and then displays 7E before even starting to fill. I can’t find anything binding. I removed the water wall track and it moved smoothly. I saw people on the internet saying that there is a problem with a magnet getting weak from the heat and no longer activating the sensor at the end of its travel. Could this be my issue? How to resolve?
- Guest asked 5 years ago
- last active 5 years ago
Above Samsung dishwasher flashes lights for “Smart Auto” and “Normal”. User manual says it is a “heating over temp” error. Could not find tech sheet on unit (I don’t think they put one on the unit.). I Kept a service mini manual from a previous. Looks like the temp thermistor is bad, not the PCB. Has anyone else run into this type of problem with this brand?
- Fred Abernethy asked 8 years ago
- last active 8 years ago
HOW DO I TROUBLESHOOT THIS? I SUSPECT BAD WATER VALVE. NO WATER IN TUB AND COMING UP WITH U6 ERROR CODE. THANKS.
- mdhomeservices asked 6 years ago
- last active 6 years ago
Water leaking to pressure switch area through black hoses.
I dried the area and AE back again.
When I opened door I saw water being directed to front of door on ledge from water input.
- Guest asked 7 years ago
- last active 7 years ago
Hi,
I turned on the Lower drawer to my Fisher Paykel 2-drawer dishwasher and pushed the start button. Instead of engaging, it made a short beep sound, followed by several rapid beeping sounds. There weren’t any error symbols displayed.The upper drawer works fine. The lower drawer gave no indication of problems and worked fine the night before. Since that time, I have been using half of a dishwasher for several months. Help!
- Guest asked 6 years ago
- last active 6 years ago
I am getting a 9C1 error on my samsung dishwasher.
- Don Kopecky asked 4 years ago
- last active 4 years ago
My Dishwasher is displaying a AE6 error code.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
Question is about this repair: https://www.appliancevideo.com/premium/samsung-dw80j9945us-dishwasher-leaking-from-the-sides-of-the-door-water-wall/
I’m actually having an issue with the 7e error code trying to find information in regards to that replaced the sprayer arm assembly as well as the motor that runs it still giving the same code trying to see if there is a test for it or if I have to run the machine through test mode so that it understands it has a new motor new motor is running the old one would not but it is making a thumping noise like as if it is trying to run one direction to far or the other direction to far
- Guest asked 6 years ago
- last active 6 years ago
My Blomberg dishwasher (model: DWT 34240 NBL00) is showing error code “IF” then “88” and then “IF”. All the 4 wash cycle lights glow continuously and no button works except “ON/OFF” push button.
- Gary asked 9 years ago
- last active 9 years ago
