Appliance Type: Dryer

I hope someone out can help me out on a frigidaire dryer getting e-61 error code replaced main control board. Try to reset unit per instructions. Not working dryer giving me same code. Any ideas?

This samsung dryer is running for 2 min. then drops to 1 min. left and ends cycle. I noticed the back legs had dropped off the top of the washer. I lifted it back up and cleaned sensor bars, but cycle still shutting off in 3 min. Any ideas?

I followed the instructions doing everything stated on your video found at this link.Everything checked out ok.
https://www.youtube.com/watch?v=OpZXoD16uvs

After doing these things the dryer ok ran for a couple days but then the thermostat reset button began popping out again. I replaced the thermostat with an OEM new one and the dryer ran ok for a couple days. Now the new thermostat button is popping out again and has to be reset. It’s happening so often that I drilled an access hole in the front of the dryer so I can just
reach in and reset the button when it pops. Any thoughts about what to do next?

The dryer powers on but doesn’t start. Pressing the start button gives 3 beeps almost like the door isn’t closed. I put the dryer into test mode and all I get is error code EHd, this doesn’t appear in any diagnostics codes anywhere. The control panel appears to be responsive. None of the error code sheets show this error code.

There was a large amount of lint being blown out the back of the dryer and I cleaned out the outlet. I’m about to take apart the bulkhead to get to the blower and vacuum that out too.

MACHINE DOES WORKS. DISPLAY “AF” ERROR CODE.ELECTRIC DRYER.

Hello this specific issue is on a Kenmore dryer 796.81172210. The cooling light stays on and there is no heat. I have replaced heater which solved the heat issue but my question is why is the cooling light staying on??

I have experienced this issue many times in Samsung dryer especially once it’s fixed the heaters on and the light stays on after repair Any thought to why this is?

Is there a self diagnostic mode. If so please explaine how to use it.

I have a Kenmore Elite Dryer and I keep getting a F code. I have cleaned the lint trap but it keep stopping.

I have a customer that wants me to convert his LG dryer to LP. It is an LG model # DLG3171. I typed this number into your model # guide, with no results. I checked PartsPro website and that number came up. So I know that it is a good number. Do you have a video for this model # or something close to it showing how to take it apart? And 2, how long should a job like this take?
Thank you
Bob

Hello, I pulled the cover off my igniter on my gas dryer, and the flame will ignite for about 5-10 minutes and then goes out.

my dryer is making a loud squealing noise.

We have a customer that has this dryer and the red lock light is on and the clean lint filter display is on, unit will not work. Unit has been cleaned out lint vacuumed as well as vent being cleaned. Any ideas.

     Need Help on a GE  Dryer, This unit will only run for Five minutes an then shut off,

You can Press the start Button and it will Start back up, but you can set the Control to
Air only and it will then run Normal. Could this be in the Control or the Thermister
problem ? You can set the control To No heat and the Dryer will then
Run Normal. I am thinking it may be a bad thermistor or Main Control, Need your help.

Can you give me some help, I would appreciate it.
First let me tell you, my dryer is completely apart! When the dryer was put on “Time Dry” it did not dry the clothes. It at first got slightly warm. And then went thru the whole time without drying the clothes.
What would you consider the most likely part(s) to be ? And how would I go about testing the component(s) with VOM?
Thanks for your help and time, Rich.

Hi,
I looked at the titles of repair videos in your list. There are 3(I think) available LG Dryer repair videos that may be the issue, but the model number is different from mine……
1) Does that make a difference?
2) Do I have to purchase each video to find out how to fix it?
3) How can I tell which video will address my dryer’s problem?
4) I saw video titles for other brands of dryers (GE, Samsung, etc). Are the different brands and models so different from mine that one won’t apply to the other?

Hello, I have a dryer the is showing an e71 error code. all the sensors are checking out good the only thind is one of the 3 coils is bad would that cause an e71 code?

The thermal fuse on heater keeps blowing, the thermostat, fuse, and thermistor have all been replaced but problem persists. We have checked and air flow is not an issue. What else can we do.

it started by squeaking alot. repair guy’s solution: spray wd 40 and saying “see, it’s not sqeaking now”. $75.00 that cost me. within a month noise was back. took it apart. drum roller on right side ground down the little fiber washer but was moving ok. I replaced both drum rollers and washers of course and the damn belt pulley also. worked for a while then eventually started making a grinding noise…due to the the drum hitting the front cowling or whatever it’s called. find metal filings at bottom in front. I replaced the guides (the blue and cork ones) worked well for a while and now it’s grinding again. I can reach inside the machine and lift the drum in front and it moves 1/2 to 1 inch when I push toward the ceiling. I need to figure out how to keep the drum from tilting down in front. I thought of wedging something small under the guides in front to raise them up but don’t know if it would create enough lift to get the drum off of the part it’s grinding on. Any bright ideas are most welcome….other than “get a new dryer”

Allan Tomson

Found the belt shredded last year and replaced it, but seems to have happened again. How can it be going through them so fast since the customer doesn’t use it on that consistent of a schedule? I can replace the belt again but don’t want to do this every year. and cover the cost of the part if something else is going on.

Timer motor will run to cool down part of cycle but won’t advance to off. The dryer ran from 10pm to 4am on cool down,