0 votes
2k views

My freezer is leaking water from somewhere.

0 votes
2k views

The lights on my control panel will not come on.

0 votes
1k views

There is a layer of frost covering everything inside.

0 votes
2k views

My icemaker has been making hollow icecubes.

0 votes
1k views

The door on my freezer will not stay shut.

0 votes
2k views

My GE freezer will not turn on or do anything.

0 votes
1k views

The interior light flashes as well, when I close the door I can reset my temperature to my desire setting until the doors open again then it resets once again. You may contact me at 606-349-6700 or 606-349-6717.

Thank you for your time and have a nice day

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

I’ve checked evaporator coil for ice buildup. No ice, fan is working, freezer thermostat has continuity , freezer thermistor good, door seal in good shape and clean, no gaps, condenser is running but hot to touch, relay isn’t clicking, no unusual noises, door controller reading”high temperature” ,set on lowest setting #7 temperature is 23. Any ideas?

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
3k views

Ice filter not changed in two years and existing small amount of cubes are small.

What is the method to cycle ice maker and perform test:

I will assume I have to fix a defrost thermostat/thermistor assembly. I need to be able to test and disassemble freezer back panel and ice maker Dissasembly.

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
2k views

THE UNIT COOLS FINE, HOWEVER, THE “DOOR AJAR” ALARM LED IS LIT AND BEEPS. I HAVE GONE THROUGH THIS UNIT AND COULDN’T FIND ANYTHING WRONG WITH THE INTERIOR LIGHT CIRCUIT, WHICH IS CONTROLLED BY THE DOOR SWITCH. THIS LED ME TO BELIEVE THE FAULT WAS IN THE BOARD. I HAVE A NEW BOARD INSTALLED AND HAVE THE SAME ISSUE. ANY IDEAS? THANKS

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
2k views

THE UNIT SHUTS OFF AT ABOUT 30 DEGREE F. THE T-STAT IS A DISCONTINUED PART. I HAVE OTHER T-STATS BUT I WAS LOOKING FOR THE WIRING DIAGRAM SO I CAN FIGURE OUT IF ONE OF THESE OTHERS WILL WORK. THE T-STAT HAS 3 WIRES AND A GROUND. I’M THINKING ONE WIRE IS ASSOCIATED WITH THE DEFROST CYCLE? ANY HELP WOULD BE APPRECIATED.
THANKS
HAPPY NEW YEAR
BILL

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

THE “DOOR AJAR” ALARM KEEPS SOUNDING. IT STOPPED FOR ABOUT A WEEK AND THEN CAME BACK. I CHANGED THE DOOR SWITCH WITH NO EFFECT. THE UNIT IS COOLING WELL AND THE DOOR SHUTS PROPERLY. I’M THINKING IT’S IN THE BOARD. ANY THOUGHTS WOULD BE APPRECIATED.
THANKS

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

Not cooling properly in freezer

0 votes
2k views

I have an issue with a Freezer, it’s a Frigidaire and this is the problem I am seeing: Intermittent cooling

0 votes
2k views

Can you tell me what could be causing this issue on a Frigidaire Freezer? It is having these problems: Not cooling

0 votes
2k views

My Frigidaire refrigerator runs too loud.

1 vote
2k views

the unit says vacuum condenser.
however the middle section of the back wall is over flowing with Frost.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1k views

Hello, We have a freezer that doesn’t keep the temperature and everything thaws. We empty the freezer and then it starts working again.
We would like to know what is wrong, what parts we need to get, and need help in fixing it.
this has happened before, and it worked for a year and it happened again. It is definitely something that needs to be fixed and we want to repair it before we use it again.

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
3k views

Compressor won’t run. No power to compressor.Do you think the computer board is bad or the thermostat dial control?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

I have a customer with an upright freezer. It stands taller than a regular fridge. Well I’ll get to the point. After diagnosing the problem, I proceeded to put the back evap cover panel back on AND I put the screw right thru the coil tubing. Ah s#~}%~~! I couldn’t believe that the screw hole was a 1/4 inch from the coil.
Well ” things happens” and it seems to happen to me an awful lot. The model / serial numbers that I gave to you, are barely readable, so I don’t even know IF they are correct. I offered to work something out with the customer, which turned out FOR ME to be a nightmare. She is a pack rat. It took me over an hour to remove the freezer from her house, because there was ONLY a path to get from one room to another. She had junk everywhere….
I took the freezer to a fellow repair tech that fixed the hole, blah blah blah. An hour after I dropped of her freezer, she called me to find out the status on it. One hour! I got several calls. So, I just stopped picking up the phone.
I offered to turn the case over to my insurance company but that was not an option…. So, I can’t tell you how many hours I spent trying to fix and satisfy this customer.
Here is my question, for further reference. I’m NOT going thru this again. Is there a website or something that I could use to determine the value of an appliance, and just pay the customer a fair price ?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
14k views

why does Kenmore upright freezer top shelf have a big big frost built up none of the other shelfs do this this is a very simple unit manual defrost no interior fan.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

I am not getting any power to the fan or compressor.
I disconnected the plug that leads from the power source to the box below the door switch.
there is power going into the box but not going out of it meaning supplying the compressor and fan ect

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

I think this is a simple freezer could it be the control board that fried up the comp relay and does this have a defrost timer on the back thanks

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

so the temp in the freezer is not freezing.
i open the back unit the coils are frozen .
i put the unit into defrost and i can hear the ice melting . however i believe there is too much ice for it to melt before the cycle is done.
i tested the timer and it went back into a normal cycle what can the issue be?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
219k views

I asked you last week about a Kenmore upright freezer that I determined to have a bad compressor. I got there and the temp in the freezer was 68*. I was told that it stopped freezing a few days ago, ( probably more than that ) and so I checked the evap/fan and it was working fine. So, I pulled it out and checked the compressor and it was so hot, I could barely touch it. I unplugged it for about 15 minutes and put a hard start on it, because the relay was bad. Let it run for about 20 minutes. Both the compressor and hard start were hot.
I was schooled to think that if the compressor is that HOT, and has been running like that for a while; that it’s NO GOOD. The reason is, as I was told, that the high temp breaks down the oils, etc in the compressor.
My customer had another freezer ( chest type ) and it was also NOT freezing. I opened the compressor panel and checked the temperature of the compressor and it was HOTTER than her upright. ( sho has a coffee plus shop ). I told her that both freezers were no good.
Anyways she called her refrigeration service people out. He told her, that the only thing wrong with the chest freezer is that it needs to be defrosted.
QUESTION: was I schooled correctly to think that if the compressor runs that hot for an ” unknown ” period of time that it is NO GOOD?

  • Guest asked 8 years ago
  • last active 6 years ago
0 votes
2k views

I have a customer that has a Kenmore upright freezer.. It’s reading “Hi-Temp”. “7 on the controls. Before I go and look at it, would you please send to me the service manual for this, or let me know WHERE you get them? Because, I looked on the Internet and couldn’t find it. Second, do you know why it’s reading high?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

replaced board on Kenmore freezer 24hours ago part #216979600 was not running now its cold but flashing

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

The temperature in the freezer at 17 degrees
I cleaned the coils and I feel cold air blowing inside the freezer as well

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My Kenmore freezer is not cooing properly.

0 votes
2k views

My GE freezer is not getting cold enough and water leaking on to floor.

Showing 31 - 60 of 83 results