Appliance Type: Standalone Freezer

The temperature in the freezer at 17 degrees
I cleaned the coils and I feel cold air blowing inside the freezer as well

Frigidaire model#GLFH21F8HWE

I asked you last week about a Kenmore upright freezer that I determined to have a bad compressor. I got there and the temp in the freezer was 68*. I was told that it stopped freezing a few days ago, ( probably more than that ) and so I checked the evap/fan and it was working fine. So, I pulled it out and checked the compressor and it was so hot, I could barely touch it. I unplugged it for about 15 minutes and put a hard start on it, because the relay was bad. Let it run for about 20 minutes. Both the compressor and hard start were hot.
I was schooled to think that if the compressor is that HOT, and has been running like that for a while; that it’s NO GOOD. The reason is, as I was told, that the high temp breaks down the oils, etc in the compressor.
My customer had another freezer ( chest type ) and it was also NOT freezing. I opened the compressor panel and checked the temperature of the compressor and it was HOTTER than her upright. ( sho has a coffee plus shop ). I told her that both freezers were no good.
Anyways she called her refrigeration service people out. He told her, that the only thing wrong with the chest freezer is that it needs to be defrosted.
QUESTION: was I schooled correctly to think that if the compressor runs that hot for an ” unknown ” period of time that it is NO GOOD?

I am not getting any power to the fan or compressor.
I disconnected the plug that leads from the power source to the box below the door switch.
there is power going into the box but not going out of it meaning supplying the compressor and fan ect

My GE freezer will not turn on or do anything.

Need daignostic sheet or manual for model GBE10ESJBSB

why does Kenmore upright freezer top shelf have a big big frost built up none of the other shelfs do this this is a very simple unit manual defrost no interior fan.

The door on my freezer will not stay shut.

I have a Whirlpool Model GI6SDRXXQ02, Serial # K11191550 Refrigerator that accumulates ice below the freezer section about an 1/8″ thick and then water leaks out onto the floor as the freezer door has frost due to the icing. This just started this year and I have had this Ref. 6 or so years.

Model – 253.26082100 Serial – WB63832311

Display in door flashing CE. Disconnected / reconnected wiring harness from control board that goes to display. Did not changed anything . Found upon opening door slowly display would clear out CE and then come back as you moved door.
Suspect wiring harness in door problem. Parts breakdown shows harness in bottom of door, but no part number. Anybody come across this before? Are you able to replace this harness? Thanks in advance

My icemaker has been making hollow icecubes.

This standalone freezer is not getting power to the compressor. Turned the defrost timer and still nothing. Not sure how to test the timer. Or test the cold control

I would like to know how to put this freezer into the defrost cycle. it was frosted up, so i took it apart and defrosted it. the heater was ok. the defrost thermostat read open even frozen in the ice. after I jiggled the wires a little then it showed good. I replaced it anyway. I would like to put an amp clamp on it while its cold and kick it into defrost to make sure its fixed. i know some of them you open the door a couple of times. I would like to know the sequence to put this one in defrost .

Frigidaire upright freezer control on door had an “8” and was not running. Unplugged freezer and it worked again. I suspect it was flashing “E” and “8”. I checked servicetips.com service manual, file name ends with 5995531505. It says E8 is a shorted thermistor. Do I need to go back and check this? Is replacing the thermistor the only part needed or is there a pcb/control (besides the one in the door) needing to be replaced?
I need some feedback from someone who has more experience with these freezers.

There is a layer of frost covering everything inside.

I have customer with above model, and issue is freezer is not freezing to desired temperature, it only reach up to 2 centigrade, I change, thermistor/ temperature sensor. I check compressor running dry well, I also change relay and new capacitor. But still I am not able to reach temperature up to -10 and above, what should I check oe change the parts to recommended. Thank you.