Appliance Type: Standalone Freezer

why does Kenmore upright freezer top shelf have a big big frost built up none of the other shelfs do this this is a very simple unit manual defrost no interior fan.

I am not getting any power to the fan or compressor.
I disconnected the plug that leads from the power source to the box below the door switch.
there is power going into the box but not going out of it meaning supplying the compressor and fan ect

The door on my freezer will not stay shut.

I have a Whirlpool Model GI6SDRXXQ02, Serial # K11191550 Refrigerator that accumulates ice below the freezer section about an 1/8″ thick and then water leaks out onto the floor as the freezer door has frost due to the icing. This just started this year and I have had this Ref. 6 or so years.

Model – 253.26082100 Serial – WB63832311

Display in door flashing CE. Disconnected / reconnected wiring harness from control board that goes to display. Did not changed anything . Found upon opening door slowly display would clear out CE and then come back as you moved door.
Suspect wiring harness in door problem. Parts breakdown shows harness in bottom of door, but no part number. Anybody come across this before? Are you able to replace this harness? Thanks in advance

My icemaker has been making hollow icecubes.

This standalone freezer is not getting power to the compressor. Turned the defrost timer and still nothing. Not sure how to test the timer. Or test the cold control

I would like to know how to put this freezer into the defrost cycle. it was frosted up, so i took it apart and defrosted it. the heater was ok. the defrost thermostat read open even frozen in the ice. after I jiggled the wires a little then it showed good. I replaced it anyway. I would like to put an amp clamp on it while its cold and kick it into defrost to make sure its fixed. i know some of them you open the door a couple of times. I would like to know the sequence to put this one in defrost .

Frigidaire upright freezer control on door had an “8” and was not running. Unplugged freezer and it worked again. I suspect it was flashing “E” and “8”. I checked servicetips.com service manual, file name ends with 5995531505. It says E8 is a shorted thermistor. Do I need to go back and check this? Is replacing the thermistor the only part needed or is there a pcb/control (besides the one in the door) needing to be replaced?
I need some feedback from someone who has more experience with these freezers.

There is a layer of frost covering everything inside.

I have customer with above model, and issue is freezer is not freezing to desired temperature, it only reach up to 2 centigrade, I change, thermistor/ temperature sensor. I check compressor running dry well, I also change relay and new capacitor. But still I am not able to reach temperature up to -10 and above, what should I check oe change the parts to recommended. Thank you.

I changed the duck bill drain per you video (it was stopped up) and installed the new pea trap drain with no problem yesterday. I didn’t have time to get the ice out of the bottom till today..just finished doing that..I still had water on the floor this afternoon. Could it be because I didn’t get the ice out till today or am I frozen somewhere else?? I can see a frozen trickle of ice in the back right corner of the freezer. Thought about using a hairdryer in that area but I’m not sure if I should.

Everything checks out on this as far as components. I did find the drain line frozen and advised them to thaw for up to 48hrs to ensure it melted completely. For some reason I didn’t think this happened on these models very often and kept assuming to find an issue with a part. Should I just have them monitor for proper operation? Would be great to know this was the cause.

Hello, We have a freezer that doesn’t keep the temperature and everything thaws. We empty the freezer and then it starts working again.
We would like to know what is wrong, what parts we need to get, and need help in fixing it.
this has happened before, and it worked for a year and it happened again. It is definitely something that needs to be fixed and we want to repair it before we use it again.

The lights on my control panel will not come on.

UPRIGHT BUILT IN FREEZER, THE CONTROL PANEL WENT BAD ON IT. THE FREEZER STILL HAS POWER.
NO DISPLAY AND NO COOLING

Our 3 yr old upright frost free kenmore freezer (2845) seemed to be cooling erratically and I noticed ice build up on the freezer bottom floor. I cleaned the ice off the floor and checked for leaking food – none. The ice has returned. I looked at your videos and think the problem may be a clogged drain. However, I’m not sure how to get at the drain on this model. Thanks for the advice!