My GE microwave is unresponsive and shows nothing on the display panel.
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
this is Kenmore/lg microwave oven. my question is can a magnetron test good and still be bad?
- Guest asked 9 years ago
- last active 9 years ago
The door will not stay closed on my Samsung microwave
- Fred Abernethy asked 9 years ago
- last active 9 years ago
Does everything but heat(no heat).
Would these give quartz heat and Mag heat/ one without the other? Would it heat at all if the Mag is down?
Thanks,
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
My Whirlpool dryer is making a loud noise not heating and has a burning smell.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
I’m looking for the control that this error calls for, do you guys carry it? Going to start there and then possibly do the humidity sensor as well. Thanks.
- David Sutton asked 9 years ago
- last active 9 years ago
So I had a noise filter burn up. Checked the magnetron and it’s bad. So replaced mag, cap and diode and as soon as youug it units trips the breaker. I’ve check all the wires and all the components and I can find what’s grounding causing the breaker to trip. Any ideas?
- Guest asked 9 years ago
- last active 9 years ago
I replaced the computer because it was working intermittent it’s still doing the same thing
- Guest asked 8 years ago
- last active 8 years ago
My Kitchen Aid wall oven microwave combo, that the halogen bulb in the microwave keeps failing every six months. Has anyone seen this situation before?
- Fred Abernethy asked 8 years ago
- last active 8 years ago
Has SE error code any suggestions ?
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
GE microwave that just shuts off after about 10-15 seconds and then resets to where you have to set the date and time. I am thing PCB, any suggestions?
- Guest asked 8 years ago
- last active 8 years ago
Microwave has no power no digital read out.
Panasonic is the brand name
- Guest asked 8 years ago
- last active 8 years ago
ciruct barker is good but im not getting any power to the unit
- Guest asked 8 years ago
- last active 8 years ago
My GE microwave has no power and is completely unresponsive.
- Curtis Appliance Repair asked 8 years ago
- last active 8 years ago
The turntable on my Kenmore microwave will not move.
- Fred Abernethy asked 8 years ago
- last active 8 years ago
My GE microwave is getting power to it but will not start.
- Fred Abernethy asked 8 years ago
- last active 8 years ago
My GE microwave works for a few seconds then stops.
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
The cavity light inside my kitchenaid microwave is not coming on.
- Don Kopecky asked 8 years ago
- last active 8 years ago
My Frigidaire microwave is giving off a burning smell when in use.
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
My GE microwave will not shut off.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
I would like to know what this error code means and what can I do to fix it?
- Guest asked 8 years ago
- last active 8 years ago
The customer says that she does not get heat from the unit regardless if it’s in microwave or convention
But the unit dose have power
- Guest asked 8 years ago
- last active 8 years ago
Microwave blow 1 of 20 amp fuses. Replace it and test circuits before plugging in. Disconnected the mag tube and tested diode gate. Turn power on display came on set the clock. Blower fans works on all speeds. When you set the cook time it the start swich blows the same 20 amp fuse. Looks like a bad short circuit. What do you think the problem can be. I tried everything?
- Guest asked 8 years ago
- last active 8 years ago
Getting error code f8e5 exhaust air temp sensor can’t seem to find a part number for that
- Guest asked 8 years ago
- last active 8 years ago
The microwave won’t start, what could be the problem?
- Guest asked 8 years ago
- last active 8 years ago
The board on this unit was flicking off and on and constantly beeping. Will do this while the unit is idle. I changed the control, everything seemed ok, get a call and now the board says needs service and is beeping. Any ideas?
- Guest asked 8 years ago
- last active 8 years ago