0 votes
2k views

Light is out.

0 votes
2k views

My Whirlpool dishwasher will not run

0 votes
2k views
0 votes
2k views

why is this unit not making ice cubes

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

The problem was that it was not making ice. It is a KitchenAid under counter ice maker. I put it through the self cleaning cycle twice and after it made ice, but then the customer called back saying it didn’t make ice after I left. When I went back I unplugged it for a few minutes then plugged it back in it would make ice one time then quit again. The ice maker does not have a tech sheet to run self diagnostics. Does anybody have a tech sheet or know where I can get one? Do I have a bad PCB? Does anyone know what is wrong with this? Also there is a ice wall in the back, is this supposed to be there? It is solid covering the back so I cannot reach back there without breaking it, which I do not want to do if it is supposed to be there.

0 votes
2k views

The brand in Manitowoc Ice Inc. I am not familiar with commercial icemakers, I got called out this one and I need your help. When the machine is turned on, the water will run over the vertical ice tray. The back of the tray is at zero degrees. A little ice does form on the trays edges. Also there is a cover over the vertical ice tray that opens to release the ice when in harvest. But right now when the cover is closed the water continues to run. How is the correct operation of this icemaker? Also is there a video that I could view? Thank you for your help, Ricky.

0 votes
2k views

Have issue with Scotsman ice machine. Contactor closes pump runs compressor starts runs no fan I think unit tripping contractor opens due to hi pressure. Check one side fan power from contractor and the other from main board not getting power from main board. The board is very expensive does anyone have information on unit all help appreciated

0 votes
2k views

K board has been replaced by two different techs ice forms drops sheet onto grid stays there when pulled amps on grid its .8 amps what is the normal voltage to cutter grid. Serial is k13507719 kitchenaid

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Getting error code 1 ? Model fc85a. Serial 000690 any ideas meister stand alone ice machine

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

The Ice in my Kitchenaid icemaker is melting and clumping together.

0 votes
2k views

I have an under counter ice maker and it has good water pressure to the unit but will not produce any ice. Where do I start the diagnoses ?

0 votes
3k views

I have a stand alone ice maker with the square grid wires.The ice will not produce and drop into bin.

0 votes
2k views

The unit fills up 1/2 way with ice.
My tech ordered an thermostat. Any help is greatly appreciated.

0 votes
6k views

One of my customers has a Summit model BIM44 which has been horribly maintained. I found everything scaled up, especially the distribution tube over the evap. Pump sounds like it’s running smoothly back there, but it appears the intake from the sump is blocked. I feel like it just needs a proper flush and cleaning. Any tips greatly appreciated!

0 votes
3k views

I have a GE Fridge MN:PFFSS6PKWBSS, SN: AR075158. The IM produces a few batches of ice per day. The IM cycles when I hold down the cycle button for 10 seconds and it fills with water. The duct seems to have good airflow to the compartment and the sensor mounted in the back checks out fine. Any ideas?

0 votes
3k views

I have a model 3151 ice machine which had a bad cube size control. The new control looks different in its terminal designation, and the darn part came with NO notes on how to adapt to the new control. The old one had a 1, 2 & 3 terminal marking. The new one has 4, 5 & 6. Have no idea where to place the wires properly..anyone else been here?

  • Antonio R asked 9 years ago
  • last active 9 years ago
Showing 31 - 48 of 48 results