0 votes
2k views

The problem was that it was not making ice. It is a KitchenAid under counter ice maker. I put it through the self cleaning cycle twice and after it made ice, but then the customer called back saying it didn’t make ice after I left. When I went back I unplugged it for a few minutes then plugged it back in it would make ice one time then quit again. The ice maker does not have a tech sheet to run self diagnostics. Does anybody have a tech sheet or know where I can get one? Do I have a bad PCB? Does anyone know what is wrong with this? Also there is a ice wall in the back, is this supposed to be there? It is solid covering the back so I cannot reach back there without breaking it, which I do not want to do if it is supposed to be there.

0 votes
2k views

why is this unit not making ice cubes

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
6k views

One of my customers has a Summit model BIM44 which has been horribly maintained. I found everything scaled up, especially the distribution tube over the evap. Pump sounds like it’s running smoothly back there, but it appears the intake from the sump is blocked. I feel like it just needs a proper flush and cleaning. Any tips greatly appreciated!

0 votes
3k views

Hello I have a question on a Whirlpool Ice Maker. I’m noticing these issues: Block of ice on Freeze Plate

0 votes
2k views

Need help looking for service manual ZDIS150ZSSE, ZDIC150ZBBE , ZDIS15SSHALH , ZDIS15SSHARH

0 votes
2k views

The unit fills up 1/2 way with ice.
My tech ordered an thermostat. Any help is greatly appreciated.

0 votes
2k views

Having an issue with an Ice Maker

0 votes
3k views

I have a stand alone ice maker with the square grid wires.The ice will not produce and drop into bin.

0 votes
2k views

Having an issue with an Ice Maker

0 votes
2k views

The ice maker may stop making ice if Max Ice is selected.

0 votes
2k views

I have an under counter ice maker and it has good water pressure to the unit but will not produce any ice. Where do I start the diagnoses ?

0 votes
2k views

Unresponsive

0 votes
2k views

Lights are out, Will not produce ice, Unit will not run.

0 votes
2k views

The Ice in my Kitchenaid icemaker is melting and clumping together.

0 votes
2k views

I have an issue with a Ice Maker, it’s a Whirlpool and this is the problem I am seeing: Uneven Ice cubes

0 votes
3k views

Getting error code 1 ? Model fc85a. Serial 000690 any ideas meister stand alone ice machine

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Hello,
A few months ago, I ran the cleaning cycle on our ice maker. After it completed, everything returned to normal and all seemed fine. Within about couple of days, I noticed a mildew smell coming from the bin. The ice did not smell but there was a nasty moldy smell coming from somewhere inside the bin. I replaced the all the hoses (drains, recirculation hoses, etc) because they looked cloudy and a little nasty. I also found the writing harness from the control box to the connector bracket had a wire that was loose in the harness due to corrosion. I replaced that harness. Put everything back together and everything was fine for a couple of days but the mildew smell came back. I did some deeper checking of things and found a couple of issues.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

the lights are on. water is running, but the ice maker is not making any ice.

  • lue asked 6 years ago
  • last active 6 years ago
0 votes
2k views

K board has been replaced by two different techs ice forms drops sheet onto grid stays there when pulled amps on grid its .8 amps what is the normal voltage to cutter grid. Serial is k13507719 kitchenaid

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

drain pump kicks on and all the water is pumped out and of course the machine stops and doesn’t finish the ice

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

After make ice and fill bin start melting ice completely

0 votes
2k views

Have issue with Scotsman ice machine. Contactor closes pump runs compressor starts runs no fan I think unit tripping contractor opens due to hi pressure. Check one side fan power from contractor and the other from main board not getting power from main board. The board is very expensive does anyone have information on unit all help appreciated

0 votes
1k views

what should I test or part I should try

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

The machine is cleaned regularly and still looks like new although over 10 years old but recently it has been making a churning noise from the pump and noticed the water reservoir not filling all the way or not filling. 8 have turn off and on after resting it for 30 minutes and it will make another sheet but 5he same thing. The water flow each time I start the machine is strong as always but can’t figure out the problem. I’m pretty handy and have replaced parts over the years but this one has me stumped and nothing is on the internet with these systoms.

  • recklem asked 5 years ago
  • last active 5 years ago
0 votes
2k views

The brand in Manitowoc Ice Inc. I am not familiar with commercial icemakers, I got called out this one and I need your help. When the machine is turned on, the water will run over the vertical ice tray. The back of the tray is at zero degrees. A little ice does form on the trays edges. Also there is a cover over the vertical ice tray that opens to release the ice when in harvest. But right now when the cover is closed the water continues to run. How is the correct operation of this icemaker? Also is there a video that I could view? Thank you for your help, Ricky.

0 votes
2k views

Sir,
the ice maker is warm inside the cabinet and it is making a surge of water noise.
The unit was working fine and then stop.
The unit has been cleaned and its still not working.
PLEASE HELP

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1k views

Danby ice maker will not stop to harvest cubes. keeps running until there is a huge slab of ice on the mold.

  • user asked 4 years ago
  • last active 4 years ago
0 votes
2k views

Customer complaint is the cubes are small, and only a handful of small cubes unit runs fan runs.
Have not checked the unit yet, do you have a service manual on this Scotsman stand alone ice maker unit.
Any advise and service information would be helpful as I have not checked the unit yet. Thank you in advance for your help.

  • billtilley asked 7 years ago
  • last active 7 years ago
Showing 1 - 30 of 48 results