Hello,
A few months ago, I ran the cleaning cycle on our ice maker. After it completed, everything returned to normal and all seemed fine. Within about couple of days, I noticed a mildew smell coming from the bin. The ice did not smell but there was a nasty moldy smell coming from somewhere inside the bin. I replaced the all the hoses (drains, recirculation hoses, etc) because they looked cloudy and a little nasty. I also found the writing harness from the control box to the connector bracket had a wire that was loose in the harness due to corrosion. I replaced that harness. Put everything back together and everything was fine for a couple of days but the mildew smell came back. I did some deeper checking of things and found a couple of issues.
- Guest asked 9 years ago
- last active 9 years ago
I have A Haier ice maker that is not dropping ice.
- James Buchanan asked 8 years ago
- last active 8 years ago
I have a model 3151 ice machine which had a bad cube size control. The new control looks different in its terminal designation, and the darn part came with NO notes on how to adapt to the new control. The old one had a 1, 2 & 3 terminal marking. The new one has 4, 5 & 6. Have no idea where to place the wires properly..anyone else been here?
- Antonio R asked 11 years ago
- last active 11 years ago
Need service manual on GE nugget Ice maker UNC15NJ
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
I have a GE Fridge MN:PFFSS6PKWBSS, SN: AR075158. The IM produces a few batches of ice per day. The IM cycles when I hold down the cycle button for 10 seconds and it fills with water. The duct seems to have good airflow to the compartment and the sensor mounted in the back checks out fine. Any ideas?
- Patrick's Appliance Service asked 11 years ago
- last active 11 years ago
Need service manual on UCC15NJII Stand alone Ice maker
- James Buchanan asked 8 years ago
- last active 8 years ago
One of my customers has a Summit model BIM44 which has been horribly maintained. I found everything scaled up, especially the distribution tube over the evap. Pump sounds like it’s running smoothly back there, but it appears the intake from the sump is blocked. I feel like it just needs a proper flush and cleaning. Any tips greatly appreciated!
- Fred Abernethy asked 11 years ago
- last active 11 years ago
Hello I have a question on a Whirlpool Ice Maker. I’m noticing these issues: Block of ice on Freeze Plate
- Fred Abernethy asked 9 years ago
- last active 9 years ago
Need help looking for service manual ZDIS150ZSSE, ZDIC150ZBBE , ZDIS15SSHALH , ZDIS15SSHARH
- Harley Clark asked 8 years ago
- last active 8 years ago
The unit fills up 1/2 way with ice.
My tech ordered an thermostat. Any help is greatly appreciated.
- Hall Refrigeration asked 11 years ago
- last active 11 years ago
- Guest asked 8 years ago
- last active 8 years ago
I have a stand alone ice maker with the square grid wires.The ice will not produce and drop into bin.
- Hall Refrigeration asked 11 years ago
- last active 11 years ago
The ice maker may stop making ice if Max Ice is selected.
- Harley Clark asked 8 years ago
- last active 8 years ago
I have an under counter ice maker and it has good water pressure to the unit but will not produce any ice. Where do I start the diagnoses ?
- Patrick's Appliance Service asked 11 years ago
- last active 11 years ago
Lights are out, Will not produce ice, Unit will not run.
- James Buchanan asked 8 years ago
- last active 8 years ago
The Ice in my Kitchenaid icemaker is melting and clumping together.
- Harley Clark asked 10 years ago
- last active 10 years ago
I have an issue with a Ice Maker, it’s a Whirlpool and this is the problem I am seeing: Uneven Ice cubes
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
- Guest asked 8 years ago
- last active 8 years ago
Getting error code 1 ? Model fc85a. Serial 000690 any ideas meister stand alone ice machine
- Guest asked 10 years ago
- last active 10 years ago
the lights are on. water is running, but the ice maker is not making any ice.
- Guest asked 8 years ago
- last active 8 years ago
K board has been replaced by two different techs ice forms drops sheet onto grid stays there when pulled amps on grid its .8 amps what is the normal voltage to cutter grid. Serial is k13507719 kitchenaid
- Guest asked 10 years ago
- last active 10 years ago
drain pump kicks on and all the water is pumped out and of course the machine stops and doesn’t finish the ice
- Guest asked 9 years ago
- last active 9 years ago
After make ice and fill bin start melting ice completely
- Guest asked 7 years ago
- last active 7 years ago
