Appliance Type: Stove / Oven / Cooktop

After speaking with the Kenmore service and parts department, they concluded that my gas valve to bake was either clogged or broken since the broiler element works and we didn’t smell gas when we tried to use the bake control. I didn’t find a video on how to replace or clean the gas valve. We got down to the valve but don’t know where to go from there. Do we access it from the back to replace it or do it from the oven? Do you have a video

the oven comes on, and eventually heats, but seems to constantly re-ignite. the heat element stays on, but the gas flow seems to stop then come back causing a re-ignition of flame. It does longer than it should to reach temp and then has difficulty maintaining.

How to get smooth top off to change out element

My gas stove has three smaller burners and one large, hotter burner on the front right side (in my house, next to the wall). Can the large burner be moved to the front left side, next to the counter, where I would use it more easily?
thank you!

Is this my thermostat causing problems or maybe the control? I need to get this going for the holiday. Would appreciate some help.

I’m getting an error code on my oven display that I looked up and it says it’s for the probe? But my husband checked it and it is working properly. So what do we do now? I don’t want to replace it anyway if it’s fine.

I replaced the clock oven control unit with a like part. Made all connections same way as on old part.
Still no heating to burners or oven. Clock will light and ask to reset time, but goes off when turn off the knobs to burner.
Is there some other part that could be bad.

No heat to burners or oven,

I’ve got this thing apart and have been checking parts to find the problem. It was tripping the breaker consistently and now I’m not sure what’s causing it. Checked the board, seemed fine. Checked the igniter, also good. Getting proper power to and from unit and the wall, so can anyone help me out?

Our oven worked perfectly through Thanksgiving (thank goodness!) but last night I’m pretty sure it didn’t heat up to the preheat temp even though it said it had and beeped as if ready. Dinner took much longer than normal to cook and I’m wondering if something isn’t right. I’m going to have my boyfriend take a look at it if someone could point me in the right direction on what to check?

I have a couple elements that have gone out on my stove. Is this pretty easy to do myself if I buy the parts? Don’t want to put a lot of money into this thing cause we’re moving soon. Couldn’t find a video so hoping somebody there can.

coming for dinner and one of my burners is stripped.
my number is 412-580-5300
thanks
fred

I can scan a photo of the stove. The florescent light bulb us just behind the clock, etc and is 36:inches in length. Do I have to move the stove away from the wall to replace the bulb, or is there an easier way?

My GE oven doesn’t seem to be cooking correctly. It beeped like it preheated, but when I put dinner in last night it didn’t cook it. Hours later it still wasn’t done. Burners on top work fine, checked to make sure it was getting gas. Maybe a thermostat?

I thought it was odd that our stove tripped a breaker, as soon as I reset it, it seemed fine. What should I check on it to ensure it doesn’t keep happening?

I just changed both hinges on the oven door but there is still a fill finger gap between the door and oven on the left (when facing the oven) side of the door and you can fee much more heat there than on the right side. Wonder what other issues this could be? I have a new gasket as well. Could the door be warped? Thanks!

Power on key pad functions, oven light works. I checked oven sensor, both elements resistance within tolerance. I can hear relays cycling continuously ever 5secs, but elements and oven don’t heat.

Both the bake and broil elements in the lower oven do not heat up. Any help will be appreciated. I would also appreciate it if any one could send me a schematic or wiring diagram for the subject oven. Thank you.

In the bottom oven the bake element doesn’t glow, it heats slightly though. The element itself tested good. As it is trying to heat a clicking noise comes from the back. Could this be the thermostat or something in the control panel?

I have a customer with a Maytag Gas Range, MGR7775WS 2, R10414233. This unit doesn’t have an ignitor but has a spark mule for the lower oven and it doesn’t always light on the first try. Is this something to worry about and is there anything that can be done about it?

I need to find parts for Verona through Eurochef. Any help will be greatly appreciated

GE Stove This model has a pilot light and pilot gets bigger when oven is turned on but the burner does not light.

GE Wall Oven Double m#JTP56WD1WW
I replaced the main control board and bake element. The oven calibrated fine, worked for a couple of batches of cookies, now when I set bake to 375, it does not get above 270

I’ve just tried to use my broiler for the first time, even though I’ve had this oven for awhile already, and it doesn’t work correctly. It seemed to preheat, but then when I put my fish in, and set the timer, it seems to have shut off on it’s own. I started it over, did the same thing. Is cooling down and not staying on even though it says it is.

my husband says that he checked the igniter and it ohm’s out as being fine. He says it seems like the “spark isn’t reaching or big enough to ignite the burner.” Does anyone there know what could be happening here?

looking for the replacement ignitor caloric range RJP363 has original round ignitor.0068016 this was the one ignitor that had the different mounting bracket in the kit to convert it to flat ignitor . this was never converted. There is a flat ignitor replacement but it doesn’t have the brackets in the kit i need 0309150 kit

I am replace a control board on a GE wall oven model JGRP16GEP1BG. Problem is the instructions to wire the cooling fans are completely useless, the wiring diagram came with 3 sheets. The first sheet has some useful info on installing jumpers and the bake and broil relays, but the next two pages were from a front load washer on installing a soap dispenser, these were all stapled together! There is a third relay which I will have to do a live test to see what that relay is doing if anything.