Appliance Type: Stove / Oven / Cooktop

I’m not sure how to approach this one. But here goes. My customer calls me up complaining about her top oven. She tells me on the phone that she sets the oven at 350′. And when it reaches the temp. The temp numbers go out, and the oven lock comes on
So I go to her house. Turn the oven on 250′. It preheats in minutes and the control board is fine. ??? So, I increase the oven temp to 350′. A few minutes pass and the temp reaches the setting and everything is fine. I never had an issue with it. It worked for me.
So, I go home to look up the model # to see what I can find out. And there is no model # showing up. Only one site showed a number CLOSE to hers, but the “O” is missing. I found ZET2PL1SS, not ZET2POL1SS.

1st question, is why doesn’t the actual model # show up?
2nd question, is what is going on with her top oven?

Good Evening Matt, do you have the service manual for this unit. Has an e84 error code, customer states they hear a pop noise before the code displays.

Thanks

I checked the ohms on this temp probe and it read 1080. I was told that it should read at least 1100 at room temperature.
Is the probe ” bad ” at a 1080 reading “
Would it cause a delay in raising the oven temperature to 350 at set temperature? A delay of 30 minutes and the oven never reached its set temperature. Plus, when the temperature rose to about 310* it began to drop gradually to 295*

PA020047 Replaced spark module on numerous Viking ranges and like one or two a month randomly die and stop working completely. Have bought them from numerous sources (speedy parts, reliable parts, eBay, Amazon, allvikingparts etc) online including the whirlpool replacement which is an exact replica and even that one has died on me. Some last a week, some several months before I get a callback. All the new ones seem to be made by RobertShaw and not Ivensys like the old ones not sure if they’re all the same manufacturers or not.

The control board is defective and has been worked on before. I want to verify whether someone may have switch the wires around on the control board

complaint, only portions of numbers light up. Oven works ok. If you set it for 325F , part of the 3 & 2 is not lite up. Whats going on?? Is this some type of error code??

so i figured it maybe the control board so i changed it.
when i return power to the unit the bake and prob lights were flashing nothing seems to work and then the f7 error came back non
please advise

i changed the igniter i changed the gas valve and nothing seems to correct the issue.
the igniter will not glow .

Left rear burner on this gas cook top will not spark. I have changed the switch harness and the spark module. You can take a screwdriver and lay on top of the ignitor and it will spark. I have checked the wires and don’t see any bare spots and also the ignitor is new. Any suggestions or ideas?

Does this unit have any service flashes or job pointer concerning the bake burner and spark ignitor kit .This is a DSI system? The gas ports are clean. The oven has run for years with out the Ground supplied through the outlet. The wiring is good. No bare insulation.

Is there a service manual available?

do you have the wiring diagram for this unit?

video on how to replace rack sensor

Parts break down of unit.

Replaced igniter on the bake and works great. also replacing igniter and valve on the broiler but it doesn’t light BUT THE IGNITOR COMES ON AND GAS COMES IN for more than several minutes with door closed. I drilled two small holes near the broiler igniter and flame started to catch but new problem now there’s a draft Whirring noise when it runs and backfires… is there a kit to address this??

This unit needs the 2 right infinite switches replaced. You can no longer get just one switch, you have to buy a switch kit with a wiring harness included. I have the part needed W10307362, but it came with no instructions at all. Can you get me the installation instructions? A video of this would be great if you have one available.

THERE IS ANOTHER PART TO THE CONTROOLL WHERE DOES IT BELONG

How do I unlock bottom door.
I can remove oven because it is not mounted to cabinet with screws. It takes two people unless there is another way using dolly or other method.
I believe safety thermal fuse has blown. What location is fuse.

The user interface on this oven will not work at all. Acts completely dead. No clock display, and none of the buttons work, unless you turn any of the burners on. Then the touch pads work correctly. Then you can set the oven to a temperature and it will say preheat for about 5 seconds then the display goes dead again. One more thing the burners never actually heat up when you turn them on and if you turn the burner off during any of this the screen goes dark and acts like it has no power.

Hello, have a GE gas oven set to bake @ 350 starts to preheat will only reach 250 and oven shuts itself off. Try it again same thing, shuts its self off at 250 as if you hit the cancel button. Clock stays lite up. I tried self clean cycle and it seemed to work ok, door locked, fan started running. I stopped it before it got too hot so I could get the door to unlock without having to wait for the oven to cool down. Tried the broiler burner
, it seemed to be working ok. Tried bake again at 350 and it reached 350 with out shutting off. I thought great its working. Tried bake the next day same problem, oven shuts its self off at 250 wont go any higher. Is there some special setting or feature on this oven causing this???? Made sure the keep warm setting was off.

Is it normal for the upper oven to heat up 15 min longer than the lower? If not what can repair it?

THE CONTROLS WILL NOT WORK

oven won’t hold temperature , f7 error code

Right front burner switch stopped rotating. Got a new switch. Installed it per your Feb 2015 Utube video. The new switch did not turn either. So, here is where it gets odd. I removed the switch, stuck the knob on it and it turned just fine while in my hand. Did the same test with the original “defective” switch and it turned just fine as well. Re-installed each one and neither turns when installed. Help please

My customer has this large Thermador oven, and the power went out. This caused just the main large oven to not function at all. It just displays Call Thermador for Service. Everything else works except for the main large oven. I wanted to see if you know how to reset this main board or know what is causing this issue.

the stove top sparks are not working I did not hear anything at any burner that I try.
I will light only with a match

I removed the control module and replaced,the touchpad. The display no longer works but everything else,does. Did I leave,off a wire which I can’t find, or is something else going on.

Eoc is blank. Vac good.

GE cooktop that doesn’t stop ingniting. We have replaced the spark module and the wire harness switches, problem continues. Any suggestions as to what it could be?