Appliance Type: Stove / Oven / Cooktop

THIS IS SECOND TIME ASKING WHAT COULD BE PROBLEM
AND WHAT IS OHMS ON SAFTEY VALVE WOULD BE TWO PIN ON TOP AND TWO PIN ON BOTTOM
PLEASE LET ME KNOW THANKS SO MUCH

What would make one of the hot surface lights on the stove top stay on even the the burner isn’t hot?

hi so we have 2 issues with the stove top.
1. the two middle burners will not light by itself i hear the clicking but it sparks at the rear right not the middle where i want to light it.
2. the left and right front burners have a real small flame.. there is very very little gas flowing to the burner hence the small flame

Whenever unit is set to self clean winth 90 minutes it shuts down with an F9 error message according to customer have replaced control and checked for proper operation of door latch assembly all other functions work properly what could be the issue?

f3 e2 error when you use the micro I replaced the erc because there was no display now I get this code and I already checked sensor I was thinking about installing another erc

The burner and infinite switch part number is w10823734. The espy sensor harness on the old and new sensors won’t work on the new INF SWitch . or would it be simpler to use the old burner with the 12002121 INF SWITCH?

I need a wiring diagram. And any help you can give.

Replaced control board, but still not heating in the oven and the stove top. Any help would be great. Thanks, Todd from NY.

when I turn on the stove it show me error f 7 and f 9. it don’t let me do nothing. It don’t let me press bake. when i clear those number it come back again. I can not used the oven. I don’t have problem with the top. what i need to do? do i need to reset?

So it takes a long time for it to preheat the igniter is fine after some time the oven shuts off but the preheat light remains on

The controls on my cooktop are not working.

Thermador

Looking for a video that help me to replace the Ignitor switches.
Key point. Do I need to take off the gas valves of every single ignitor switch?
General Videos of different Models they don’t show that gas valves need to be taken off.
Video has be for that specific Model CGS1740ADH S/N: 15221545WU.

Thanks for your help.

I changed the infinite switch and it did the same thing.
If I begin on low it will heat and cut off but will not come back on even after 10 minutes. If I turn it off and then back on it repeats the same cycle. It will stay on high. If I set it on 3 or 4 it does the same.
Can this be the sensor in the burner?
How does it work?
It doesn’t matter if I use the single or dual settings.

115 volt one leg of bake element, other leg 70 volts not enough current/volts to power element

Have a unit with no display when powered up. Display will come on when microwave door is opened and clock can then be set. Lower Oven can then be programmed and will start to heat as long as microwave door is opened. Lights also get very bright while oven is heating (oven and microwave lights both come on when either door is opened).If microwave door is closed relays can be heard clicking then display and oven both turn off. If microwave door is opened then clock display comes back up; although if you wait awhile before opening the door it just reverts to power failure mode. Relay board was already replaced to no effect.

Oven. Would not bake. Replaced e.o.c. Now the oven will come on but the bake element only gets 110 to it so it will only get warm. If you put it into broil the broil element works. When I put it into bake no voltage come out of relay with the yellow wire coming out of it that goes down to the bake element. Checked wires from control to bake element they check out ok. Any help would sure be appreciated. Thanks

Evan if i put to 250 only the broil heating element goes on

The door lock is no longer available. Is there a way to bypass the door lock?

I have a 48″ Jenn-air range ; that main oven flame was sputtering and shut off. I started smelling gas and called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

There is a fuse link in behind the control board on this model that is blown. It resembles a diode a little. I cant find this part on any drawing and was wondering if you could help me with the part number to this fuse?