0 votes
2k views

My stove is not getting any power, and I checked the breakers, and they are fine. What could this be?

  • Joseph asked 10 years ago
  • last active 10 years ago
0 votes
3k views

I’m pretty sure I need to replace the convection fan. I have identified the replacement part online. But I can’t figure out how to get to the back of the oven to get to the convection fan. Do I get there from the inside? Or do I need to take the whole over out of the wall to get at it from the outside? Any videos to help? Thanks.

  • Michael asked 10 years ago
  • last active 10 years ago
0 votes
7k views

Hi, I wanted to find out how to replace the element in my oven? It cracked and broke in half while I was using it and my neighbor said I could probably handle replacing it myself. Would you advise this? I’m not sure if it’s something I could do or not. Any help would be appreciated!

  • Andrea asked 10 years ago
  • last active 10 years ago
0 votes
2k views

The pressure regulator is marked for lp as well as nat.gas. Is this regulator built to be able to change from one to the other?

  • Jerry Goehring asked 10 years ago
  • last active 10 years ago
0 votes
2k views

when I turn on the stove it show me error f 7 and f 9. it don’t let me do nothing. It don’t let me press bake. when i clear those number it come back again. I can not used the oven. I don’t have problem with the top. what i need to do? do i need to reset?

  • sonia roldan asked 10 years ago
  • last active 10 years ago
0 votes
2k views

The gravy went down the valve stem hole onto one of the Valve Switches. (The orange colored square switch can be seen looking down the valve stem). Could this short out that one valve switch and cause ALL burners to spark ignition when the unit is plugged in? If so, what is the procedure to disassemble the unit to replace that valve switch. Also, could that gravy spill have caused damage to the Spark Module? If so, where is it located on the model?

  • Bill Gale asked 10 years ago
  • last active 10 years ago
0 votes
3k views

I have a Kitchen Aid Superba double oven. The upper oven is lighted with the probe icon. i can not get the oven to heat or to shut the icon off. i have tried inserting the probe and removing it to no avail. the lower oven seems to working properly ,. Can you please advise.

Thanks in Advance
Scott Hynes

  • Scott Hynes asked 10 years ago
  • last active 10 years ago
0 votes
3k views

My top oven will not heat. When I put it on self clean the top burner inside the oven lights up and then begins the self clean. However when I go to heat something up on say 400 degrees, it does nothing…..very strange what is going on? It is obviously getting gas, but when I go to bake with the top oven it will not work.

Now the bottom oven is working, but we rarely have used it. Is this a flaw with Kitchenaid. The oven is only about 2 years old.
Thanks for the help!
Ryan

  • Ryan asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Baking oven fan blades hit the back of the oven. Removed the oven from the cabinets and tightened the bracket holding the fan. Seemed to work for about 2 weeks, now rattling again. I noticed when I tightened the assembly that the motor pivoted up and down and wondered at the time if this was normal. The screws holding the motor to the bracket are not loose so I am perplexed. Any ideas. thanks

  • kurt troeger asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Is there a video showing how to replace the thermostat, or do you think it is something else. This started after running a self clean cycle. Thank you.

  • Sandra asked 9 years ago
  • last active 9 years ago
0 votes
2k views

It’s gas by the way. What part would I need?

  • Tyler A asked 9 years ago
  • last active 9 years ago
0 votes
2k views

There is no problem with the oven preheating but when it attempts to cycle on again, the gas doesn’t ignite – the spark igniter can be heard. The issue wouldn’t be the temperature sensor, since the unit calls for heat. The spark igniter can be heard. Is the issue most likely the safety valve?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

how do I access the switches

  • Ron asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Every time I baked three or four trays of pastries I have this problem. The heat would not go up on the the third or fourth one. Every thing else is working. I baked one at a time.
Please let me know the problem.
Thank you.
Barlen

  • Barlen Ramasawmy asked 9 years ago
  • last active 9 years ago
0 votes
2k views

During preheat period, the oven temperature does not reach preset temperature while when baking period starts, the temperature in the oven continues to get hotter beyond the preset temperature (it does not turns off). Oven temperature sensor was replaced but problem persisted. Microwave works fine after board was replaced. Are there any other parts (thermostat, thermal controls, etc.) that the board will control for the oven and need replacement?

thanks,
ao

  • Arturo asked 9 years ago
  • last active 9 years ago
0 votes
2k views

I’m hoping you can determine if this is my ignitor failing, possibly the thermostat, or something else altogether. Most times it heats fine, bakes correctly. Other times it doesn’t seem to hit temperature, or falls short. Looking for some confirmation before replacing parts. Thanks.

  • Roger asked 9 years ago
  • last active 9 years ago
0 votes
3k views

It seems like it always happens if I put a wet pan on the stove.

  • Diane asked 9 years ago
  • last active 9 years ago
0 votes
2k views
0 votes
2k views

light in the oven is always on , the turn off key seems is not working and as well some other 2 o 3 keys. my guess is i need to change the membrane, but , how i will konw if is just the membrane and not the the coen ntrol too. there is not teck sheet in the oven or else where. i do not want to give a wrong estimate to my costumer because the control is too expensive, one of the control is $279.17 and the membrane $140.00 if i added together both is so much. menbrane pt# 9756595bt- control pt# 9762812

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

The entire touch pad works except for Bake, Broil, and convection. All the digits and timers clock keep warm, pizza, the rest of the key pad functions. Tried to reset by unplugging. Didn’t work. Oven comes on by using the pizza function. Top burners work as well. Why only a few not work?

  • Ronda asked 9 years ago
  • last active 9 years ago
0 votes
2k views

If the igniter is broken, does the oven still send gas to the burner tube when turned on?  I only ask as it’s not lighting, so I tried to turn it on and light it manually, and apparently there’s no gas coming from the burner tube.  I just want to make sure the igniter is the problem.  Everything else works on the oven – all four top burners and the broiler. which is at the top of the oven.

  • Bill asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Broiler on oven won’t shut off

  • Steve Hanshaw asked 9 years ago
  • last active 9 years ago
0 votes
3k views

TRIED TO CHECK BAKE ELEMENT. CUSTOMER SAID NOT BAKING GOOD OR GOING INTO SELF CLEANING. HOW TO GET TO IT?

  • Mike Lloyd asked 9 years ago
  • last active 9 years ago
0 votes
2k views

I have a double oven maytag and my bottom oven will not heat up when I turn it on to preheat it stays at 100 degrees. I replaced the bake element so why won’t my oven heat up?

  • LaRonda Hunter asked 9 years ago
  • last active 9 years ago
0 votes
2k views

I have this gass stove , kitchenAid Model # KGRI801PBS00.
Costumer complaint: make short circuit , tripeed braker (or blow out braker) at braker box , then He restore power and blower motor kept running all the time ( non stop).
I take off the touch panel with the control box behind the touch panel and restore power blower fan motor kept running , so, I hit with my screw driver the relay board , the one is located behind the surface and get the motor stop .
But when , I put back the touch pad with the control is at back the touch panel and press the bake , the braker at braker box when off again (braker tripped).
another interesting question that I have is: I take away the cables going to the motor and check those cables for ground it was grounded , when the plug is inserted in the wall outlet, but if , I take away the plug from the wall outlet , now is not grounded is that ok?.
Now I , think I have problems with one of the board ,but I don’t know , which control board or even if the touch panel .
How I will determine or probe each one of this control or touch panel. thank for your help, wating for your answer, my email address is : armandoappliances@gmail.com , or also I have this other one : armgua@gmail.com. I am fan of yours wabesite and also I was refered to you, by marcone appliance which , we have accesd I belive as a premium till December 31.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

when i turn on any top or oven, it will come on and die out..then i have to leave ignitor on until it comes on and stays very low flame before going to proper setting..

  • GENE asked 9 years ago
  • last active 9 years ago
0 votes
6k views

Our range is beeping non-stop and flashing the aforementioned error code. From what I could find online, this is a shorted keypad. So what part do I need and is there a video that could show me how? I really don’t want to have to get a new range and am hoping this won’t be too difficult.

  • Zak Thornton asked 9 years ago
  • last active 9 years ago
0 votes
2k views

TURN ON AND IT FIRES UP THEN SLOWLY DIES OUT..CAN NOT LIGHT…

  • GENE asked 9 years ago
  • last active 9 years ago
Showing 1 - 30 of 1k results