Appliance Type: Stove / Oven / Cooktop

CUSTOMER SAYS THAT THEY HIT POWER BUTTON, IT STAYS ON FOR BRIEF MOMENT AND THEN SHUTS OFF. THEY HAVE TO PRESS THE POWER BUTTON AIN TO KEEP TURNING IT ON.
ERROR CODE F34 COMES ON AFTER POWER FADES. Tried to test power line going into unit to main board but not sure if low voltage should be present.

Please help on error code F8E0

Oven light turns on by itself , how can I prevent this from happening?

Giving error code 5a6 or sab on display nothing work

This code says cooling fan speed too low or won’t come on. Do you have a video on this one and a service manual and any tips?

Seems like the main oven door is not contacting with the latch/light switch.

We have a Jenn-Air/Maytag Appliances JDS9860AAP oven, which displays an F1 error code not long after reaching a preheat temp (typically 350). After clearing the error, it eventually comes back multiple times as the oven cools and has to be cleared each time as it cools its way down.

The large oven tends to take a longer time to preheat, even though the hidden bake element and the broil element are cycling during the preheat. Also, should the throat elements be coming on to assist pre-heat, or are they only used to convect?

Customer says that they can only turn on one out of four burners. one comes on and when they attempt to activate other burners, they get intermitent flashing LED lights on readout. There are two LED readouts. one on left and one on right. after they activate the one burner and start to activate the others, the error code appears. left LED displays
” E ” and right LED displays ” 32 “. Sounds like control board but not sure.

Double oven will not work and keep getting F97. What is the likely problem? Lower cooling fan will not run. Found service bulletin that says to check connector. It’s a double oven so it will be very involved to take it down and really check it but as far as I can tell by peeking on it it looks ok. It says to replace cooling fan and sensor board if it’s ok. Is the cooling fan and sensor board more than likely bad based on you guy’s experience?
Thank you.

i have customer who have Samsung induction range, and they got error E-84. keypad is not responding, i check the all control board and non of them have burning sign, i am planning to change touch pcb both side control board, i also download service manual and it says either invertor board or touch pcb board. how i can check inverter board without doing so much disassemble cook top remove. give me good plan to check

My Electorlux range is getting an E31 error code.

when baking at 400 degrees oven door will lock can’t get food out until it cools down and food burns. It doesn’t do it all the time but most of the time. It’s GE Profile Drop in range. I notice the Fan was making a funny noise and was wondering if this could cause it to get to hot and lock up. The thermostat and control board seem to be working fine.

I have this Samsung induction range not heating and has error codes, can you provide any information on the induction range ? Thanks Tim

When set to bake, after about 20 seconds the unit codes out with f-34. tech sheet only says: replace air switch, then replace cooling fan, then replace control. all 3 have been replaced, in that order, and its still giving f34. the tech sheet doesn’t give any other information about the code. Anyone have any suggestions?

Working on this dacor wall oven originally giving a u60 error, cooling fan, installed cooling fan and we are still getting the error. Can anyone assist us with a tech sheet and some direction where to go next? Thank you.

GE Cooktop with error code F152 F

My question is what would cause the F30 error code to come up I did a preliminary search and found it had something to do with the oven probe or the main control board I tested the resistance of the oven probe and had 1.097K which looks to be correct . The manuals that I downloaded off the Frigidaire site did not have anything corresponding or any information on error codes .
I would like to confirm that the main control board needs to be replaced after checking the probe if that is what the F30 error code means

The range will randomly display error code e201
when not being used that happened twice over the last few days the oven works fine everything seems to be working fine but just getting that error when not even in use

My oven is displaying a C21 error code.

Small left oven after a couple minutes of baking in any mode the clean light comes on steady and oven light Flashes three times. The cooling fan seem to be running fine from what I can hear and I looked at the big relay at the bottom of the oven for the small left oven that is having the problems and they look to be in perfect condition and all its connectors. Can I please have a diagnostic manual that will tell me what the flashes mean?