0 votes
160 views

how to replace de31-00070b on this range
please help

0 votes
252 views

Whenever unit is set to self clean winth 90 minutes it shuts down with an F9 error message according to customer have replaced control and checked for proper operation of door latch assembly all other functions work properly what could be the issue?

  • mra20168 asked 8 months ago
  • last active 8 months ago
0 votes
196 views
  • user asked 9 months ago
  • last active 9 months ago
0 votes
158 views

You guys do this every day , what is the best manufacturer?

0 votes
151 views

Matt sorry wrong model. This is the model for the question I gave you yesterday. Jt912sk1ss.

  • rodney asked 9 months ago
  • last active 9 months ago
0 votes
279 views

Oven. Would not bake. Replaced e.o.c. Now the oven will come on but the bake element only gets 110 to it so it will only get warm. If you put it into broil the broil element works. When I put it into bake no voltage come out of relay with the yellow wire coming out of it that goes down to the bake element. Checked wires from control to bake element they check out ok. Any help would sure be appreciated. Thanks

  • rodney asked 9 months ago
  • last active 9 months ago
1 vote
206 views

This unit needs the 2 right infinite switches replaced. You can no longer get just one switch, you have to buy a switch kit with a wiring harness included. I have the part needed W10307362, but it came with no instructions at all. Can you get me the installation instructions? A video of this would be great if you have one available.

0 votes
164 views

My kitchen aid dishwasher is flashing “F1” & “E2” not sure what it means or what to do.

1 vote
221 views

Does this unit have any service flashes or job pointer concerning the bake burner and spark ignitor kit .This is a DSI system? The gas ports are clean. The oven has run for years with out the Ground supplied through the outlet. The wiring is good. No bare insulation.

Is there a service manual available?

  • Pancakes asked 9 months ago
  • last active 9 months ago
1 vote
200 views

complaint, only portions of numbers light up. Oven works ok. If you set it for 325F , part of the 3 & 2 is not lite up. Whats going on?? Is this some type of error code??

0 votes
188 views

Ikea cooktop will not turn on. Looks like something is blown. What should I check?

0 votes
193 views

I have an electric GE drop in stove. When trying to use the oven, I keep getting different codes–F1, F2, F3, F5..then have to reset. Can this be repaired?

0 votes
200 views

When I turned the oven on to 200° it went to 200° and stopped, I waited and then tried 450° and it went to 450° but then when I tried to turn it off it wouldn’t turn off and then got the error code F2

0 votes
168 views

how to replace oven door lock motor

0 votes
214 views

This is not a quick fix the microwave problem is due to a bad door switch. There are three door switches on the interlock circuit and if any one of them goes bad the unit will not allow it to start. Most times when the switch goes bad it is typically the lower one that burns out or the upper one that burns out. When that happens the unit will not be allowed to start up and run. you would need to take that apart and check out all 3 switches on the interlock circuit.

0 votes
204 views

WHEN THE TEMPERATURE IS SET, IT VERY SLOW REACHING THE SET TEMPERATURE. AFTER REACHING THE SET TEMPERATURE, IT DROPS DOWN TO A LOW TEMPERATURE. SOMETIMES, ALL THE POWER SHUT DOWN, AT THE MIDDLE OF COOKING. THIS IS A DOUBLE OVEN. ALL THE POWER GET SHUT DOWN AT THE SAME TIME. IN BOTH THE UPPER AND LOWER OVEN.

  • lue asked 10 months ago
  • last active 10 months ago
0 votes
178 views

f 20 coming on

1 vote
216 views

Viking range. Burners not clicking.
Model number vgsc3674qss.

A friend’s range. They said various burned clicked and didn’t light and finally none would light. I got there and none would click at all. I checked one of the spark switches and it had continuity when turned on. I cleaned that burner and still nothing, but I did not remove the base. The tiny screw holes were full of crap so I couldn’t even tell what kind of head was down there. I hope I don’t have to try to get them out!

I don’t want to order an expensive spark module until I’m sure what the problem is.

How should I troubleshoot this?
Tom

1 vote
232 views

We are having an issue with this wall oven showing an F6E0 error code when going into the diagnostic mode. After researching, we found it is an issue with the boards or control panel. Is there any way to test which is the faulty part causing this issue?

0 votes
188 views

Have a built-in electric oven. Has worked fine until this morning. When I push any of the features, Bake etc. iI get a reading on the center screen that says “Feature Not Available”. What do I do to get the oven to work again?

0 votes
169 views

My Whirlpool Oven says “stuck key”.

0 votes
172 views
0 votes
178 views

GE oven model JB680DT1BB, I cant see how to change the bake element? Where does it plug in, recently bought the house and the oven did not have a bake element, I have the part but the plugs are on the left and I do NOT see where it goes.

0 votes
184 views

I have a frigidaire double oven. I went to clean it and got an f8 error. I hit clear and the error went away but I can’t do anything with my oven. I turned off the breaker to the oven and let it sit. Turned it back on and the oven says locked, but it is not and it wont do anything

  • Don Kopecky asked 10 months ago
  • last active 10 months ago
0 votes
174 views

Oven was working fine and then we noted that it was in “Preheat” mode with the temperature decreasing. Tried the following, turned off and tried bake then broil, then convection – nothing changed. Opened supply breaker and reclosed. Same “preheat”. Any suggestions before we call the repair service?

  • Don Kopecky asked 10 months ago
  • last active 10 months ago
0 votes
210 views

I have a new Whirlpool double oven. We got the lower oven door off as in the instructions, but the hinges did not remain at a 45 degree angle. They popped back to a 90 degree angle, as when the door is attached and closed. I can’t get them back to the 45 degree angle to reinstall the door. When we try to install the hinge into the slot in the oven and slowly open the door toward 45 degree angle, they pop out of the slots and return to 90 degrees.

0 votes
150 views

I have a Frigidaire double oven. I went to clean it and got an f8 error. I hit clear and the error went away but I can’t do anything with my oven. I turned off the breaker to the oven and let it sit. Turned it back on and the oven says locked, but it is not and it wont do anything.

0 votes
225 views

Why does my whirlpool natural gas oven make a popping noise when it is on?

0 votes
211 views

bake shuts off after 3 seconds

0 votes
131 views

the bake shuts off after 3 seconds

Showing 31 - 60 of 1k results