0 votes
25 views

Late ignition 2 to 3 times during hour bake time
Frigidaire service says wrong ignitor or too high of amperage at intro. Smell gas at these times.

0 votes
133 views

We need a tech sheet and wiring diagram for tis range. It is electric with double oven.
Thank you.

  • user asked 3 months ago
  • last active 3 months ago
0 votes
96 views

Preheated but after that when the ignitor gets red again to light the gas it doesnt preheat. Only couple years old. Ignitor is good. But the temperature will not pass 120F. Can diagnostic manuals for this unit

0 votes
153 views

The wiring diagram is missing on this unit and we are wanting to see what board powers the cooktop portion of the Range. Any chance of finding the wiring diagram for this unit? Issue is front left burner intermittently turning off.

0 votes
158 views

Already replaced the temperature sensors but one thing we noticed was that oven was slightly warm without any use. Replaced the temperature sensors on both upper and lower oven but the customer called back saying it’s doing it again after like two months I’m starting to suspect it’s the control board?

1 vote
159 views

video on how to replace rack sensor

  • mmab24mm asked 4 months ago
  • last active 4 months ago
0 votes
80 views

I am trying to access the user interface behind the knob. I am not entirely sure that it is the main control. But the oven works with the keys but not knob. I was told it is a 90% chance it is the main control but I have no clue how to access the user interface at the top behind the knob. Please help

  • kivery90 asked 4 months ago
  • last active 4 months ago
0 votes
144 views

Im getting a E312 control error.

  • zelik123 asked 4 months ago
  • last active 4 months ago
0 votes
133 views

Good morning.
Thank you for helping me out with this issue. Apparently, the selector knob has stopped the ability to increase and decrease the digital numbers on the screen. The stove top works fine, and the buttons to select oven temp, clear settings, cook time etc (along both sides of the selector knob) work when pressed..however when i press the “oven temp” , “cook time” ,”timer” buttons the “0:00” or “0” digits appear on the screen but as i turn the knob (clock wise) to set the temp of time the digits do not move. I need your help..do you think its the mother board behind the selector knob? by-the-way..When I press the button “Oven Func” >then select Bake..then press “Oven Temp” and “0” appears on screen..even with a value of the “0” the oven will “click” on.
Please help..any assistance is greatly appreciate it!
Sincerely,
Nelson

  • dignity9 asked 4 months ago
  • last active 4 months ago
0 votes
128 views

-Replaced right side spark module twice now (CM didnt care about left side), Every time the oven is heated the whole top section gets extremely hot and spark module over heats causing sporadic clicking until it cools down an hour later
-Oven door shuts good
-Oven does NOT have a cooling fan because its a full gas range so no circuit boards to cool in back
-I put aluminum tape around spark module area directing the venting hot air away from the module housing
-I tried running the hood vent on maximum over the range to evacuate some heat, DIDNT help

I know the electric ignition one with the DSI ignition module has had a recall to install a cooling fan but this is a 13 year old range which the top of is over heating. Decently taken care of.. Any suggestions? I was thinking to run the module under the range to a cooler area but the micro switches on the valves are getting extremely hot too and brittle

0 votes
117 views

WB10X21659 HOW TO INSTALL

0 votes
133 views

I have a Kenmore gas range that after replacing the spark module oven works ok except when you turn the oven on if you try to turn the gas burners on the display goes off and the oven shuts down. If you turn only the top burners on they work fine only if you turn the oven then it shuts off oven doesn’t heat. What can I check

0 votes
149 views

The range will randomly display error code e201
when not being used that happened twice over the last few days the oven works fine everything seems to be working fine but just getting that error when not even in use

  • zelik123 asked 6 months ago
  • last active 6 months ago
0 votes
361 views

Randomly beeps “error L43 relay” when not being run. Checked both upper oven power relay and lower oven relay but no visible damage and the error doesn’t always come up only every couple hours a breaker reset fixes it temporarily. Would this be the lower oven relay? I need the diagnostic manual BUT MORE IMPORTANTLY an answer to which board it is?

0 votes
136 views

the bake and the broil work but when I put it on self-clean the door will lock and go for about a min and then it will stop
I see the blue light labeled OVEN blink 4 times and the blue light labeled HEATING blink 3 times
please advise

  • zelik123 asked 6 months ago
  • last active 6 months ago
0 votes
126 views

The wolf oven goes on by itself and turns off.
None of the burners will light without a match

  • zelik123 asked 7 months ago
  • last active 7 months ago
0 votes
140 views

I need any advice and Tech sheet

  • Pancakes asked 7 months ago
  • last active 7 months ago
0 votes
134 views

electrode not firing. do smell the gas though. large oven does work.

  • mmab24mm asked 7 months ago
  • last active 7 months ago
0 votes
182 views
  • user asked 7 months ago
  • last active 7 months ago
0 votes
216 views

In this particular unit, when I first arrived , the bake TCO was bad. I replaced the TCO and the oven part itself worked great. However, the convection fan will turn on then turn off with the clicking of a relay for something. I did find out that the convection element is bad as well. My main concern is, why does the convection fan turn off and on like it is doing? I have never seen a convection fan do this. I have replaced the convection board on this unit as of today, and it still does this. Is this maybe a faulty main board, or will it stop when I put in the new convection element?

1 vote
176 views

THERE IS ANOTHER PART TO THE CONTROOLL WHERE DOES IT BELONG

0 votes
181 views

upper oven wont unlock door lock can not remove side trim to get to installion screws to remove oven

  • ed asked 8 months ago
  • last active 8 months ago
0 votes
205 views

I was looking for a service manual for this particular unit the issue is an F3 error code and I like to see if I could compare the oven sensor resistance to a wiring diagram

  • Tca2018 asked 8 months ago
  • last active 8 months ago
0 votes
340 views

The burner and infinite switch part number is w10823734. The espy sensor harness on the old and new sensors won’t work on the new INF SWitch . or would it be simpler to use the old burner with the 12002121 INF SWITCH?

I need a wiring diagram. And any help you can give.

  • Pancakes asked 8 months ago
  • last active 8 months ago
1 vote
208 views

Oven works but no burners on top do. Are they controled by the oven control somehow or what else could cause all of them to quit?

  • wayne asked 8 months ago
  • last active 8 months ago
0 votes
246 views

After burner light up the spark ignitor continue to spark, this happen only on right front and right rear burners all others are fine.

0 votes
751 views

i have customer who have Samsung induction range, and they got error E-84. keypad is not responding, i check the all control board and non of them have burning sign, i am planning to change touch pcb both side control board, i also download service manual and it says either invertor board or touch pcb board. how i can check inverter board without doing so much disassemble cook top remove. give me good plan to check

0 votes
196 views

I have a gas range that was flagged by the gas company CO levels to high. I have a detector but didn’t bring it with me ( I was informed it was a gas leak and just brought my sniffer) Visual inspection showed a normal blue flame in oven .It is in a small apartment with no vent and the gas company didn’t leave any ppm #s .what should I be looking for to feel confident it’s not the oven just the size of apartment and no ventilation?

0 votes
302 views

Do you have a video on how to remove the control panel.

  • rodney asked 8 months ago
  • last active 8 months ago
Showing 1 - 30 of 1k results