Appliance Type: Washer

got a combo Kenmore washer/dryer, there is a11/2inch gap between the washing basket and the body at the top causing articles to full into the washer and mess up the drive belt and speed sensor, the real question is where does the speed sensor and bracket attach and secondly if there should be a gap at the top.

How do I get the tub out of this washer

what is the easy way to replace the water valve?

When you start the washer all the lights go on, you cannot program a cycle, and the washer starts and has sound, water comes in, not agitating.

so the unit gives me an error of F5E2 i changed the door lock and i am still getting the error,
i hear it making noise when its trying lock as if the part that locks is rubbing against something. please advise

replaced 4 suspension and the sensor problem not fixed
what do you think is the problem

I press start button but it doesn’t start, how can enter into diagnostic mode in this unit.?

The customer called said she was getting the u.e. Code. I told her to stop machine and redistribute the load. She does that but it doesn’t help. The machine tries to relevel then she says it starts to wash all over. She says the washer will run for over 2 hours. Does Samsung have a problem with this model or a recall. The suspension and balance ring all seem to be ok. An suggestions. Thank you.

When I run a cycle on normal it goes until 37min then stops . When you it on spin and drain it starts at 13 min and shuts off at 8 min.

I need to replace the door lock. I need to open console , how do open? do you have a video on the complete job? a Kenmore top load.

Washing machine goes off balance in the high speed spin. Will take a long time to finish.

The washer fills then stops. If you restart it again, it squirts a little water then stops. No agitate or spin.

The lid switch is defective and I’ve ordered a replacement.

Hello
Have a problem with my Whirlpool washer Model LSR8433KQ0.
The agitator works and fresh water will come into the tube,
but when the timer moves to any “Rinse” position the dirty
water does not pump out and the spin cycle doesn’t happen.
There is a humming noise when the timer goes over the “Rinse”
position but nothing happens.
Removed the pump, motor, and checked the motor coupling.
Outside the unit the motor shaft turns easily and turns the pump shaft.
I can turn the rubber/plastic coupling still inside the machine with my hand
and it turns the agitator OK.
Your expertise for a repair solution is very much appreciated!
Regards
Bruce

Need service manual and tech sheet

Could it be a bad motor sensor ?

On Quickwash cycle the machine doesnt go into high speed spin. The clothes are still soaking wet at the end of the cycle.

I turned the clothing drum and it moves freely like good working washers

I blew air into the drain hose and air bubbles came up in the drum with water in it

So the question is should I replace the drain pump or just try to unclog it somehow

Looking at the manual it suggested it was a clogged drain pump as the third possibility

Thanks. Carey

No error codes come up. The clothes are getting clean. What makes the agitation on the agitator? When the water fills to a certain level is this when it supposed to agitate. You can see anything because of the lid lock. I assuming that it does. Is there any way to see why it is agitating? Also is there a video to show to how to change the diverter valve. The one I have is leaking right under the diverter pump.

this washer works. recently has started to make noise in spin. if load is heavy it smells like something is burning. what are the necessary parts. can this washer be repaired without special bearing replacement tools?

I’ve changed the MCU in CCU and I am still getting the f11 error I do not see or hear the motor or the tub turning

removed bottom panel and manually unlocked door, tried cycles, will fill & drain, will not tumble, once door locks can only unlock manually, I think it is the lock assembly, ordered part, worried that motor didn’t tumble? any suggestion?
Thank You
Joe

I SEE WATER DRIPPING FROM THE DEFUSER UNDER THE BOTTOM DRAWER

i can turn the drum either way but the unit will not agitate or spin.
it dose drain

Hello Guys, my question is regarding a Samsung direct drive inverter washing machine top load. with a load of clothes spin speed is slow clothes remain wet. washer does not give any codes. the machine seems to spin okay unloaded. drain pump works fine no obstructions, my thoughts were that it might be the clutch assy. also thought it might be a drive motor. needed a more experienced techs. opinion. would appreciate your guidance. Thank you for your help.

I have a friend that is farther than I want to travel. His washer is making noises and sometimes stops mid cycle. I’d like to talk our way on the phone to find the problem.
Will you send me (us) the diagnostic code ? Or better yet, direct me on how to get this very important tool or where to look for it WHEN I need it when trying to troubleshoot ANY appliance that I’m working on?
Thank you

The error code uL comes up every time the machine is used even when there is nothing in it. I tried a new rps sensor and didn’t fix the problem. I’m thinking it may be the main board. looking for help with this one.
Thanks, Charley

MACHINE DOES NOTHING, WHEN YOU TURN ON.

Diagnose why washer will not spin?

When I push the power button select cycle push start normally the you will hear the door latch lock and the sensing light will light then the washer will go thru its regular routine of going thru the wash cycle. Now when I push the power button, select the cycle, push the start button NOTHING WILL HAPPEN, NO ERROR CODES!