0 votes
2k views

Hi,
Do guys have any service manual for this unit?

The customer complains that the machine will stop mid cycle and won’t turn back on, My tech took the dryer apart and now the dryer won’t start at all and just make a clicking sound. any ideas?

Thx

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Leaks water, humming sound, dishes are not getting clean.

0 votes
2k views

Leaks water, dishes are not getting clean, soap does not disolve.

0 votes
2k views

Standing water, leaking water, bad smell.

0 votes
1k views

My dishwasher will not shut off.

0 votes
2k views

Buttons will not respond, start then shuts off, will not fill.

0 votes
2k views

will not fill, bas smell, slow fill.

0 votes
2k views

Door stays open

0 votes
2k views

Door is heavy, door will not close, leaks water.

0 votes
2k views

disher are not getting clean, soap at bottom of tub.

0 votes
2k views

door will not stay closed, control will not respond.

0 votes
2k views

Plastic is worn out.

0 votes
2k views

No lights, will not run, cycle shuts off, will not fill, will not heat.

0 votes
2k views

Seal is damaged, condensation under counter top.

0 votes
1k views
  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

fast wash which is a 30 minute cycle goes down to zero and then it turns back on again and went to 15 mins cycle…. for the 15 mins cycle then goes through another wash cycle….so the 15 mins wash it went down to zero and everything drained and there is no water in it now so it works on the 15 min cycle and not the 30 mins cycle (wont turn off on 30 mins but shuts off on the 15 min cycle)….for the 30 mins has to shut off manually which then leaves water in the dishwasher

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

First complain was that the dryer is making noise. We had complete open in the back of the unit and front to clean.
We put it together and power turns on and no turning the drum at all.

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
4k views

DISPLAY IS NOT BRIGHT, ORDERED PART FROM BOSCH – PART IS UPDATED AND LOOKS A LITTLE DIFFERENT. RELAYS NOT EXACTLY ON THE RIGHT PLACES, BUT THE PROBLEM IS THAT ITS GIVING ERROR CODE E-01
CANT GET IT OUT OF THE SCREEN

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

THIS IS M/W AND OVEN, NEED TO REPLACE M/W PANEL BUT CANT DISASSEMBLE THE UNIT
DOES ANYBODY HAVE ANY RECOMMENDATIONS?
THANK YOU

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

No start at all

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
3k views

bosch wap24201uc axxis

24 inch wide Frontload washer
Door won’t open clothes stuck inside

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
2k views

Fills but does not drain goes through cycle except for drain

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Unit doen’t complete the cycle and stop in the middle. Do we need a main board? It drains good.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

No lites on display panel

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

The dishwaher will not drain.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Hello, I have a bosch dryer that shuts off after 3 mins of run time heat is good timed dry cycle ok only on any auto dry cycle changed thermistor cleared condensate and lint trap still same problem any help. Thanks

0 votes
1k views

I need a tech sheet and information to pull up codes and run diagnostics.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

SUB ZERO FRIDGE SIDE How to adjust the fresh food door Because it is tilting with The top over to the right. I tried adjusting based on what I found online but it only made it worse and scrapes the other door when you open it. Can I please have the manual and for schematic of this fridge

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views
CL

the unit remain on CL
i cant not change any settings.
i tiered to rest it by the braker it did nit help
i took out all the wires to the board and it did not help.
i did change the board a few weeks before that it worked fine.
now its like its frozen nothing works all i get is a consistent CL

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
2k views

I replaced the control panel still getting power but no lights note turn on

  • Guest asked 7 years ago
  • last active 7 years ago
Showing 31 - 60 of 151 results