0 votes
18k views

Dishwasher fills and runs for a while, then stops mid cycle with an E17 error.

0 votes
7k views

My Bosch dishwasher is not working properly.

0 votes
6k views

The range will randomly display error code e201
when not being used that happened twice over the last few days the oven works fine everything seems to be working fine but just getting that error when not even in use

  • Guest asked 5 years ago
  • last active 5 years ago
1 vote
4k views

DISPLAY IS NOT BRIGHT, ORDERED PART FROM BOSCH – PART IS UPDATED AND LOOKS A LITTLE DIFFERENT. RELAYS NOT EXACTLY ON THE RIGHT PLACES, BUT THE PROBLEM IS THAT ITS GIVING ERROR CODE E-01
CANT GET IT OUT OF THE SCREEN

0 votes
4k views
e21

so the unit is getting an e 21 error. i put it into the diagnostic test mode and it will not go past s01
please advise

  • Guest asked 5 years ago
  • last active 5 years ago
1 vote
4k views

The dishwasher overfills and goes into the drain pan causing the E15 error. I cannot find a float switch that regulates how much water fills the dishwasher. What do I change to cause it to fill normally?

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
3k views

my Bosch dishwasher is leaking water.

0 votes
3k views

I’ve worked on a few of these, and found the limiter open, so I replaced that, but still having issues. What am I missing? There must be something else.

0 votes
3k views

Hello, I have an error code E207 for my Bosch oven. The latch does stick. How do I clear the error code?.

0 votes
3k views

bosch wap24201uc axxis

24 inch wide Frontload washer
Door won’t open clothes stuck inside

  • Bbcl9268 asked 6 years ago
  • last active 6 years ago
0 votes
3k views

Its fills with water and drain it right away

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

My dishwasher doesn’t want to drain completely. Initially I thought it was something stuck and cleaned out as far as possible down into the impeller or chopper area like a video I saw on here. Ran another cycle and same thing happened. Could it be something stuck further in the drain or pump area?

  • Noelle asked 9 years ago
  • last active 9 years ago
0 votes
3k views

There are not tech sheets or information here on this washer, anyone free to give me a quick look on the issue? Thanks.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

I have a E01 error code on a Ascenta Dishwasher? any suggestions

  • Rany asked 9 years ago
  • last active 9 years ago
0 votes
3k views

The unit will actually begin to smoke if there’s a heavier load in. Where should I start?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

THE UNIT RAN OVERNIGHT AND IS COLD ON BOTH SIDES. I WENT THROUGH DIAGNOSTICS AND ALL THREE FANS CAME ON. THE TEMP SENSORS ALSO WERE WORKING CORRECTLY. THE FANS DON’T COME ON DURING NORMAL OPERATION. WHAT IS YOUR OPINION ON THIS ISSUE? THIS DOESN’T SEEM RIGHT TO ME. ANY THOUGHTS?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Looking at it now and there’s no tech sheet. Thanks.

0 votes
3k views

Customer says it spins ok cycle finishes ok, the vent sends cold air out and clothes are not dry.
My first thought was to check the heat element and thermal cutoff. Unfortunately, when I spoke with Bosch, they said they dont make the heating element for this anymore and there is no replacement part number. Would you test both first ? what would test second ?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

any tips on taking this dryer apart? Pictures etc.? Can’t seem to find a video.

  • Lyle13 asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Wanted to let you guys know, we’ve had a couple Bosch’s with this complaint, and there’s been nothing wrong after diagnosing. We always check wiring, controls, motor, and heater. No stored error codes, and all safety checks come back ok. Just in case you see any out there, let us know if you actually find a problem!

0 votes
3k views

NEITHER EVAP FANS ARE COMING ON. I’D RATHER BE ABLE TO T/S IT FROM THE BOARDS BEFORE I HAVE TO DISASSEMBLE BOTH SIDES TO GET TO FANS. MY THINKING IS THERE IS AN ISSUE THERE AS IT SEEMS UNLIKELY BOTH FANS WOULD GO AT THE SAME TIME. ALSO THE UNIT DOESN’T HAVE A DATA PLATE AND I NEED TO FIND OUT THE PROPER CHARGE. SO ANY TECH SHEETS WOULD BE HELPFUL.

ALSO IF YOU CAN LOOK AT MY LAST INQUIRY, I ASKED A SECOND QUESTION AFTER THE INITIAL ANSWER. I STILL HAVEN’T RECEIVED AN ANSWER ON THAT IF COULD LOOK INTO THAT FOR ME ALSO. THANKS IN ADVANCE.
BILL

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

I have a bosch dishwasher showing an E24 code. What does this mean?

0 votes
3k views

The washer shakes pretty violently at the beginning of the spin cycle with clothes in it. Neither sock is broken, none of the block counter balancing pieces are broke or missing, and the springs look good. If you hold the outer tub assembly it will get up to full speed, but vibrates pretty bad. Any ideas? Is there a balanced ring on this unit like some Samsung washers have?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

My customer called about her kitchen sink being clogged. And when the dishwasher drained it just added to the drainage problem.

0 votes
3k views

Just installed a brand new tankless hot water heater, the pilot light will turn on for one second make a clicking sound and turn off again. The main burners will not light. What would cause a new hot water tank to not light?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Im getting a E312 control error.

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
2k views

I’m having problems with this washer. Model #WFMC1001UC/13. A few months ago I changed out the drain pump on this washer and it worked for a while. When I went this time the washer would not agitate or spin but was draining great. I checked all the wiring, plugged and unplugged all the connections. I tested the washer and then it was running well. Customer stated it was spinning fine for a couple of days. Now complaint is a slow spin. Does anyone know what I should be looking at on this washer? There is a wiring diagram in the washer but I don’t have access to tech support. Any thoughts on this would be appreciated.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

My Bosch dishwasher is displaying an E15 error code.

0 votes
2k views

Problems seem to come in pairs. I have a Bosch Dishwasher. The circulation pump lost the propeller so I was almost finished putting a new one in and the part that it subs to has a missing tab where the old one had one. They are numbered 1-4 and the #4 pin is missing and now I have no idea where to put the pink wire. Of coarse the customer was monkeying around, took the front off and the kick plate off and the wiring diagram is missing.
Any help would be appreciated.

0 votes
2k views

Door lock won’t unlock? It makes a clicking noise like is trying to unlock but can’t. Does this mean the locks bad? In diagnostic mode can you test the lock?

  • Guest asked 8 years ago
  • last active 8 years ago
Showing 1 - 30 of 151 results