1 vote
1k views

I checked the ohms on this temp probe and it read 1080. I was told that it should read at least 1100 at room temperature.
Is the probe ” bad ” at a 1080 reading “
Would it cause a delay in raising the oven temperature to 350 at set temperature? A delay of 30 minutes and the oven never reached its set temperature. Plus, when the temperature rose to about 310* it began to drop gradually to 295*

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
2k views

Fills but does not drain goes through cycle except for drain

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
4k views

DISPLAY IS NOT BRIGHT, ORDERED PART FROM BOSCH – PART IS UPDATED AND LOOKS A LITTLE DIFFERENT. RELAYS NOT EXACTLY ON THE RIGHT PLACES, BUT THE PROBLEM IS THAT ITS GIVING ERROR CODE E-01
CANT GET IT OUT OF THE SCREEN

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
2k views

ORIGINAL COMPAINT WAS A WATER LEAK FROM BEHIND THE ICE DISPENCER HOLE. NOT FROM WATER DISPENCER TUBE. TURNING OFF WATER SUPPLY CURED LEAK, SO NOT ICE MELTING. THE SLOW DRIP IS COMING DOWN THE BACK SURFACE AREA WHERE YOU PLACE YOUR GLASS.

SEPERATE ISSUE: CUSTOMER WAS USING THE ICE DISPENCER AND MAY HAVE BEEN FILLING THE HOPPER WITH BAGGED ICE (NOT SURE. MAY HAVE BEEN LEFTOVER ICE FROM ICE MAKER). WHILE DISPENCING ICE A CHUNK OF PLASTIC DROPPED INTO HER GLASS. IT APPEARS TO BE SOME SORT OF ARM/LEVER? NOW THE ICE MAKER WILL ONLY DISPENCE CRUSHED ICE. I THINK IT IS PART OF THE ICE CRUSH MOTOR ASSY BUT I COULD NOT SEE WHERE IT CAME FROM. LINKAGE ON THE TUB MOVES THE FLAP IN THE ASSY BUT IT HANGS A LITTLE.

THANKS, GEORGE.

  • triadapp asked 7 years ago
  • last active 7 years ago
1 vote
4k views

The dishwasher overfills and goes into the drain pan causing the E15 error. I cannot find a float switch that regulates how much water fills the dishwasher. What do I change to cause it to fill normally?

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
2k views

I replaced the control panel still getting power but no lights note turn on

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

the only way to turn off the motor is by turning off the power

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Just installed a brand new tankless hot water heater, the pilot light will turn on for one second make a clicking sound and turn off again. The main burners will not light. What would cause a new hot water tank to not light?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
18k views

Dishwasher fills and runs for a while, then stops mid cycle with an E17 error.

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
2k views

We are servicing a Bosh dishwasher that stays stuck on the last minute of the cycle and water remains in the dishwasher. Any suggestions where to start?

  • mytechjoe asked 7 years ago
  • last active 7 years ago
0 votes
2k views

fast wash which is a 30 minute cycle goes down to zero and then it turns back on again and went to 15 mins cycle…. for the 15 mins cycle then goes through another wash cycle….so the 15 mins wash it went down to zero and everything drained and there is no water in it now so it works on the 15 min cycle and not the 30 mins cycle (wont turn off on 30 mins but shuts off on the 15 min cycle)….for the 30 mins has to shut off manually which then leaves water in the dishwasher

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
1k views
  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

if I check water inlet valve for bosh dishwasher and it has continutity to water valve does that mean valve is ok

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

What should I look for when the lint alarm goes off and kills the dryer? On a separate call, I replaced the belt, pulley, rollers and blower wheel. I Vacuumed Out The unit and was working fine when I left. ????

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

HOW TO BREAK DOWN TO REPLACE IDLER

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My customer’s Bosch Dishwasher is having some issues. Will not stop running

0 votes
2k views

My Bosch dishwasher will not drain.

0 votes
2k views
CL

the unit remain on CL
i cant not change any settings.
i tiered to rest it by the braker it did nit help
i took out all the wires to the board and it did not help.
i did change the board a few weeks before that it worked fine.
now its like its frozen nothing works all i get is a consistent CL

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

No lights, will not run, cycle shuts off, will not fill, will not heat.

0 votes
2k views

The dryer will beep three times and will not start,does anyone have a tech guide for this unit?

0 votes
6k views

The range will randomly display error code e201
when not being used that happened twice over the last few days the oven works fine everything seems to be working fine but just getting that error when not even in use

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
3k views

Looking at it now and there’s no tech sheet. Thanks.

0 votes
3k views

my Bosch dishwasher is leaking water.

0 votes
2k views

I am having an issue with a Bosch dishwasher.

0 votes
2k views

I have an upcoming appointment for a dishwasher that the homeowner claims is not spraying as much water as before. Just in case it is not a clog in the spray arms I was just wondering how I would enter into the diagnostic mode. The homeowner claims she culd not read the serial number – sorry.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

SUB ZERO FRIDGE SIDE How to adjust the fresh food door Because it is tilting with The top over to the right. I tried adjusting based on what I found online but it only made it worse and scrapes the other door when you open it. Can I please have the manual and for schematic of this fridge

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Plastic is worn out.

0 votes
2k views

It displays zeros instead of the time requested. we replaced the control board and it still same issue. Because it does not show time, it does not start.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Im getting a E312 control error.

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
2k views

I need a new door seal for this model, anyone have time to do the lookup for me? Thanks.

Showing 1 - 30 of 151 results