0 votes
1k views

Can you get me the part number to the upper oven relay board, I can’t find any where to look up or purchase this part?
Any and all help with this unit is greatly appreciated.

0 votes
2k views

Previously asked about this fridge before and you guys helped me locate a kit which helps with heating the drain pan and drain tubings —
https://www.appliancevideo.com/repair-help/question/dacor-built-in-fridge-leaking
I have been back 3-4 times now to unfreeze that drain tube. When costumer thaws whole fridge for a day every couple weeks the fridge starts to drain fine again for couple weeks and then issue returns. I installed kit exactly as instructions asked including disabling one of the temp defrost thermistors inside to make the defrost a standard 8 hours vs auto sensing defrost 8/12/16 defrost cycles. Issue still coming back, new heated drain pan over freezing and leaking out all over evap fan which gets disabled with ice.. its a pain in the rear job anything else i can try besides redoing the heated drain pan job?

0 votes
4k views

Randomly beeps “error L43 relay” when not being run. Checked both upper oven power relay and lower oven relay but no visible damage and the error doesn’t always come up only every couple hours a breaker reset fixes it temporarily. Would this be the lower oven relay? I need the diagnostic manual BUT MORE IMPORTANTLY an answer to which board it is?

1 vote
2k views

The unit is not cooling but freezer is cold but temp is at -12 and the fridge is at 52, what could be the issue causing this?

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
5k views

Freezer evaporator is located above in the freezer ceiling and drain keeps freezing and over flowing causing water to freezer over evaporator fan. Similar issues to the GE MONOGRAMS. I know the GE has a heater pad kit too address it freezing the drain tube but what can I do here.
Also the panel is unresponsive but I’m sure that’s just a bad panel my priority is fixing this freezing drain line to the drain pan located in the top of the fridge near the compressor.
System wont let me select dacor

0 votes
2k views

Already have the diagnostic manual to a similar model. Bake element hidden but broiler element exposed. Set oven to 350 but the elements never seem to turn off after preheat to 350 exceeding 600F based on my temperature gun. Since bake element is hidden I tested the DBL relay to bake and broil element connection on relay board with the oven slightly pulled out of the wall. Both get constant 240vac until I hit cancel on panel making me believe it’s not a stuck relay. Also tested temperature sensor connection molex leading to the clock board (unfortunately after oven was hot) and as the door was open, resistance was dropping leading me to believe its most likely not the sensor but possibly the clock board not processing the readings? I’m thinking to replace sensor and clock board what do you guys suggest?

0 votes
3k views

Inspected the whole thing no burn marks anywhere on boards everything seems to be in pretty good condition but the oven randomly shuts off usually doesn’t even achieve the set temperature. By shut off I mean it just turns off the baking process as if I never set the bake. The surface burner elements inside the oven seem to be working good and fine customer says it shuts off randomly but for me I noticed it shut off when I open the door The third time while running the oven so I’m not sure if it was a coincidence or if maybe something is loose somewhere inside where I couldn’t see.. I had this issue with another dacor but that dacor completely shut off this one just turns off bake. This one is a freestanding range with the control clock that pops out when you press on it.

0 votes
1k views

I need part number for the tool

  • lopez1974 asked 7 years ago
  • last active 7 years ago
0 votes
2k views

GOOD MORNING ALL. I AM TOLD THAT SOME BUTTONS ON THE PAD RESPOND, AND SOME DO NOT. FROM WHAT I UNDERSTAND THE CUSTOMER REPLACED THE MAIN CONTROL PANEL. ANY HELP WOULD BE GREAT, AS I HAVE NEVER WORKED ON THIS BRAND STOVE BEFORE. THANKS, TODD FROM NY.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

THE BURNERS WILL CLICK

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

Need to replace the relay board (mounted on the underside of the cooktop) and the clock (oven control) on this unit. Parts 92028 & 62790. What is the best plan to get at these to replace ?

0 votes
2k views

I have a Dacor wall oven above model #PCS130B. The unit will start beeping (NO FAULTS) when not in use.
I disconnected the key pad and it hasn’t returned. I had one of these recently and had to change the user board (on the control panel ) also.
Does anybody have the test procedure for the key pad on this unit.
Thanks in adavnce

0 votes
3k views

We need your help to diagnose what is going on with this oven
It’s a dual oven and every two weeks it starts beeping and both ovens stop working
As soon someone reset a power it works fine foe another two weeks .
My tech cane out and couldn’t find anything wrong with this unit .
I guess it could be a problem with a touch pad ?
The customer is O.K to replace both but the touch pad is NLA
Any help I would really appreciate

Showing 13 results