my electrolux washer will not start the cycle.
- T&G Appliance Repair asked 7 years ago
- last active 1 year ago
Hello I have a question on a Electrolux Washer. I’m noticing these issues: Will not run
- T&G Appliance Repair asked 7 years ago
- last active 1 year ago
Clothing gets stuck, tub moves around a lot, bad smell, standing water.
- Harley Clark asked 6 years ago
- last active 1 year ago
DDO Error, Fabric Softener will not dispense, drawer will not drain, Clothes are not getting clean.
- Hall Refrigeration asked 6 years ago
- last active 1 year ago
Screen is blank, E90 Error, ERR is on display, runs then shuts off, random numbers and letters on the display.
- Don Kopecky asked 6 years ago
- last active 1 year ago
Over fills with water, Starts to fill and stops, E32 Error.
- Hall Refrigeration asked 6 years ago
- last active 1 year ago
Will not fill, will not stop filling, E22 Error.
- Harley Clark asked 6 years ago
- last active 1 year ago
Standing water, bad smell, huumming sounds, E21 Error, E22 Error.
- Curtis Appliance Repair asked 6 years ago
- last active 1 year ago
Humming and Clicking sounds, clothes are gray, soap still on clothes.
- James Buchanan asked 6 years ago
- last active 1 year ago
Clothes will not spin out, banging sounds, boot is torn.
- Fred Abernethy asked 6 years ago
- last active 1 year ago
Squeaking noise, will not always spin, burning smell.
- T&G Appliance Repair asked 6 years ago
- last active 1 year ago
Electrical Smeel, Burning smell, runs for a while then shuts off, E69 Error, E11 Error.
- Harley Clark asked 6 years ago
- last active 1 year ago
E5E Error code displaying, E43 Error, lights come on but will not start.
- Harley Clark asked 6 years ago
- last active 1 year ago
The dryer had an e63 error. I replaced the heater because it was grounded. It still has the door open error on the display. I bypassed the door switch, no fix. Could the mainboard be faulty?
ELECTROLUX
- Guest asked 1 year ago
- last active 1 year ago
Hi,
I am trying to determine what part I need to fix my dryer EFME627UTT1. Essentially, the dryer won’t start. However, it is exhibiting other strange behavior. The dryer has been in service for about two years since, 9/2019.
When I try to start the dryer, it makes three beeping noises, as it would if the door was open. The door is of course closed however. I put the dryer in diagnostic mode and it displayed an error code of ‘EHd’, flashing as ‘E’ then ‘Hd’. I do not see that code listed in the Dryer Tech Data Sheet. The dryer has a wheel to rotate through the different dry cycles. The center of a wheel has LED lights on it, indicating the time left to complete the dry cycle in minutes. When I rotate through the different dry cycles, the timer doesn’t change as it normally would. It gets stuck on particular value, once at 45 minutes, once at 55, etc. Additionally, sometimes the previous mentioned LED light doesn’t come at all when I start the dryer. However, if I put the dryer in diagnostic mode, the light will then come on and display the error code ‘EHd’ as mentioned previously.
I have taken the dryer apart to check for lint buildup, I found some, but nothing extraordinary. I am assuming its some sort of electronic problem. From some googling it seems it might be the control board, but at around $150 I’d prefer not to miss the call on the diagnoses. Thanks for the help.
- Guest asked 2 years ago
- last active 2 years ago
the programming starts normally, water and washing works, when it is on the programming to drain the water the pump does not turn off and shows error I30, I have already replaced the board and the same defect continues
- Guest asked 2 years ago
- last active 2 years ago
Frigidaire model#GLFH21F8HWE
- Guest asked 3 years ago
- last active 3 years ago