Brand: Electrolux

The dryer powers on but doesn’t start. Pressing the start button gives 3 beeps almost like the door isn’t closed. I put the dryer into test mode and all I get is error code EHd, this doesn’t appear in any diagnostics codes anywhere. The control panel appears to be responsive. None of the error code sheets show this error code.

There was a large amount of lint being blown out the back of the dryer and I cleaned out the outlet. I’m about to take apart the bulkhead to get to the blower and vacuum that out too.

Customer says that they can only turn on one out of four burners. one comes on and when they attempt to activate other burners, they get intermitent flashing LED lights on readout. There are two LED readouts. one on left and one on right. after they activate the one burner and start to activate the others, the error code appears. left LED displays
” E ” and right LED displays ” 32 “. Sounds like control board but not sure.

My Electorlux range is getting an E31 error code.

Electrolux range today, According to tech it was built by Dacor. We were transferred to Dacor and sat on hold about 15 mins and never got an answer. The customer complaint is with the racks removed he sets the unit into self clean and the light showing “remove racks” stays lit, the door won’t lock and go into self clean. With the rack rails also removed the rack switch does click like it’s working. Any advice sure would be appreciated.

Hello, I have a dryer the is showing an e71 error code. all the sensors are checking out good the only thind is one of the 3 coils is bad would that cause an e71 code?

Sides are hot to the touch, Compressor cycles off, Loud noise.

No cool in fresh food section, Unit continually runs, Will not run.

I just replaced the thermostat and found the evap fan motor cycling on and off about every 2-3 seconds. Is this a bad motor or board or ?
Why is it cycling? I have never come across a cycling motor before. It either worked or it didn’t. How can I check to determine IF it is a failing motor?
Thank you

my ice maker has quit making ice and the ice in the bin has melted. I suspect it might be a thermistor but not sure. If the thermistor was bad would it explain the change in temp in the ice maker compartment? All other areas are working fine. is there a diagnostic I can run on the unit? Code? to verify if the thermistor in ice maker is working correctly? Also, i show there are 2 different thermistors in the part diagram , can you tell me the difference. Thanks for your help.

Not heating, Long dry times.

i need to see how to align the bottom door on this unit./ I found it once but now i cannot find itVIDEO

Leaking water, Partial cubes, Ice clumps up

Water is dripping out of the dispenser on my Electrolux refrigerator.

i was wonder if anyone can tell me how to replace the door seal on this unit
item #137066300

My Electrolux refrigerator will not cool properly.

Not cooling, Ice crystals.

Will not start.

Unbalanced rotation of the drum.

I looked at above refrigerator dispenser does not dispense ice or water sporadically. I plan to replace the dispenser module (part with the lever), not the user interface pcb. Has anyone else had a problem with that part? Thanks in advance

Ice build-up in freezer, Humming sound, Whining sound.

Not cooling, Leaking water, Frozen items in freezer melt.

Clothes will not spin out, banging sounds, boot is torn.

washer not running will not enter diagnostics, beeps three times with new board, nothing else

The compressor was bad, so I replaced the compressor about a week ago, and then that one burnt up. I replaced the compressor a couple days ago and the homeowner said that it is not cooling as it should and there is condensation on the food and milk in the refrigerator. If this compressor burns up as well, what could be causing this? And what can I do to fix it?

This fridge is completely dead, have 120 at source and 120 at board. Were do I start to figure out what is taking board out.