Brand: Electrolux

When I try to push start to get the control panel to light up. The display board just blinks and beeps once and won’t turn on. Its been doing this for a while and unplugging and plugging back in usually works but is not working anymore.

Door does not lock

THE UNIT COOLS FINE, HOWEVER, THE “DOOR AJAR” ALARM LED IS LIT AND BEEPS. I HAVE GONE THROUGH THIS UNIT AND COULDN’T FIND ANYTHING WRONG WITH THE INTERIOR LIGHT CIRCUIT, WHICH IS CONTROLLED BY THE DOOR SWITCH. THIS LED ME TO BELIEVE THE FAULT WAS IN THE BOARD. I HAVE A NEW BOARD INSTALLED AND HAVE THE SAME ISSUE. ANY IDEAS? THANKS

video on how to replace rack sensor

Our Electrolux refrigerator dispenses ice intermittently. It spits ice out on the floor. We have had to shut the water off or it will spit water also. With the water off you can see and hear the dispenser turning on and off at all hours of the day or night. I need to dig into the parts to see if it is a loose wire or faulty control panel?

I need help with how to pull the stainless ring off the control panel to get at the parts.

Has anyone solved this issue before?
I have seen it reported as Casper the friendly ghost.

Thanks,
Tom

I need to remove the stainless steel trim ring that surrounds the ice/water dispenser. Do you have a technical manual showing how to do this? I don’t want to damage it. I don’t see any exposed screws.

I NEED TECH DOCUMENTS, SCHEMATICS, REFRIGERATION SHEETS PLEASE

filling and draining at same time. leaking on floor

water presssure switch working but always 120 on the wire for no o water switch. dont have any diagram or nothing to follow.
motor controller board changed already but still not working

The customer showed me a video that sounded like the pump running with the door open. She said that it shows an error code often of 10 and last time it showed 30.
Where is the tech sheet hidden? I couldn’t find it behind the door panel or behind the toe plate.
I need a copy of it and the error codes and videos.

we need a video on how to dismantle the dryer

Dryer still not drying properly. After replacing the heat element.

The dryer takes 3 hours to dry a load. I checked the vent lines, filter, replaced the heating element along with its thermostat.
I looked at the parts diagram. And what is the purpose of the Control Board,temperature,ATC ?
Should I replace any of the thermostats?
I put my temp meter on the inside wall of the dryer vent as it ran. its temperature went from 111* to 138* on time dry and It slightly rose and fell in a time of 5 minutes On more dry setting it red 128* to 148* slightly rising and falling in a 5 minute time.
Should the temperature stay or maintain a setting of ( let’s say ) 145* for a time of 5 minutes? And then gradually drop and stay at 120* for a couple of minutes?
This dryer is giving me heart burn.?

This is a Kenmore refrigerator that is built by Electrolux . It is a french door bottom freezer. There was a frost build up on freezer evaporator coil. We defrosted it and a week later it built up again. Defrost heater and termination switch checks out. What else can it be?

I have a customer with an upright freezer. It stands taller than a regular fridge. Well I’ll get to the point. After diagnosing the problem, I proceeded to put the back evap cover panel back on AND I put the screw right thru the coil tubing. Ah s#~}%~~! I couldn’t believe that the screw hole was a 1/4 inch from the coil.
Well ” things happens” and it seems to happen to me an awful lot. The model / serial numbers that I gave to you, are barely readable, so I don’t even know IF they are correct. I offered to work something out with the customer, which turned out FOR ME to be a nightmare. She is a pack rat. It took me over an hour to remove the freezer from her house, because there was ONLY a path to get from one room to another. She had junk everywhere….
I took the freezer to a fellow repair tech that fixed the hole, blah blah blah. An hour after I dropped of her freezer, she called me to find out the status on it. One hour! I got several calls. So, I just stopped picking up the phone.
I offered to turn the case over to my insurance company but that was not an option…. So, I can’t tell you how many hours I spent trying to fix and satisfy this customer.
Here is my question, for further reference. I’m NOT going thru this again. Is there a website or something that I could use to determine the value of an appliance, and just pay the customer a fair price ?