Brand: Frigidaire

I hope someone out can help me out on a frigidaire dryer getting e-61 error code replaced main control board. Try to reset unit per instructions. Not working dryer giving me same code. Any ideas?

refrigerator is not cooling at all but the compressor is running

This freezer section thawed , then rebooted and cleared has worked ok then showed h1. then before it defrosted started working again.

Refrigerator not working at all and displaying SY CE
Installed Main Control Board/Board switch kit w/ harnesses 5303918556
Took out old board, installed new, and nothing..not even error code.
Put customers old board back in, and it displays error code

Assuming I got a defective board, and purchased another one.
Re-installed new board, same thing. Nothing..not even error code.
Put customers old board back in again, and it displays error code.

Researched problem further and found out I may need to replace the board behind display on door
User Control and Display Board 241973712
Went back and installed both new boards, and still machine is not even displaying error code.
Put customers old board back in, with new display board, and error code comes up.
Everyplace I research, anytime this error occurred, tech replaced both of these boards and problem was solved.
We checked all the wiring and connections to all harnesses, and they look good.
Can someone please help me if you have experienced the same problem, and tell me how you resolved this issue?
I’m tempted to buy all new boards AGAIN, but I don’t think I could have received this many defective boards, something else has to be wrong.
Any help will be greatly appreciated, thanks in advance

Frigidaire combo laundry system, model FFLE3911QW0 stopped and I retrieved error code EC6. The entry from the tech sheet is pasted below. How should I troubleshoot this, or what are the likely causes of this?

Pump motor constantly running giving error code i30 checked drain pump everything working fine

We have aproblem with this unit. it doesn’t make any ice . We found for sure the one of inlet valve coils is open ,
but the same time we can hear some strange knocking sound from the ice maker .
We never worked on this kind of ice maker before ,it looks kind of strange one for us
Any help would really appreciate

My question is what would cause the F30 error code to come up I did a preliminary search and found it had something to do with the oven probe or the main control board I tested the resistance of the oven probe and had 1.097K which looks to be correct . The manuals that I downloaded off the Frigidaire site did not have anything corresponding or any information on error codes .
I would like to confirm that the main control board needs to be replaced after checking the probe if that is what the F30 error code means

I have a frigidaire double oven. I went to clean it and got an f8 error. I hit clear and the error went away but I can’t do anything with my oven. I turned off the breaker to the oven and let it sit. Turned it back on and the oven says locked, but it is not and it wont do anything

We attempted to repair this machine but will not respond whatsoever. It will beep when pressing the control panel buttons but will not start the cycle. We reset the stackable and the same thing occurs. We also tried replacing the lid switch and main board with no change. We also attempted to put it into service mode in order to look up the error codes in which the stackable would still not respond. Do you know of anything else that could cause this issue? The stackable will just beep three times which we thought to believe would be the lid switch.

only the heavy wash and high temp dry buttons work or will light up and when you push the start cancel button nothing happens. When you close the door the display lights up but the wash light does not come on and nothing happens. after a minute or two the display shuts off. Ocassionaly it will work bit only on heavy wash and high temp dry.
I replaced the control panel and the same thing happens. Your video showed the same symptoms and was resolved by changing the control panel. I am hoping I do not have to change the control board as that is another $100 + part.

I checked for the 13vdc at the board and replaced the fan but it still didn’t work. I checked for the 13vdc again and it only showed 7 vdc. Is it the board? It is not in the wiring is it? Isn’t there a way to check the motor with a 9volt battery and how would I do it at the board to check the wiring to the motor first before I replace the main board? I have the tech sheet. Is there any information or video about this problem?

GOOD EVENING. I SPOKE TO THE CUSTOMER AND WAS TOLD THAT THIS STARTED ABOUT SIX MONTHS AGO, BUT THEN WENT AWAY. IT STARTED AGAIN THE LAST COUPLE OF DAYS. ANY HELP WOULD BE GREAT, THANKS. TODD FROM NY.

Again, this stove is 2 years old and never been cleaned. Never. It is giving off an F10 code when plugged in. I can’t find the make of this anywhere. What is this F10 code?
Thanks

Mod# LFGF3014LBC. Ser# VF25057900

Has blinking code e68

Excessive steam coming through vent at top of door, accumulating and dripping on floor.
Anyone seen this? Ni filter or damper door, just a duct that lets steam out.

Ran into an issue today where the turn valve at the water heater was severely corroded and there’s a copper connection coming up behind the refrigerator. I removed ice from the fill tube and there is water to the icemaker, but I think it’s insufficient. We don’t do plumbing work, so what should I recommend she say when she calls someone else out to take care of this and get it properly hooked up for her?

Hi Folks,
Keep getting error codes i20 & i30. Has anyone ever had this problem? I understand that installing Part # 5304504077 will elevate of this problem. All suggestions greatly appreciated.
Thank you,
Jan,
Barney’s Appliance

Have a customer with a Frigidaire SxS .
Lights are on but its not cooling/running.
Order power board ( 5304498781 ) and install same, mounts under freezer side.
New board completely dead, no lights or anything else.
reinstall old, lights come on ok.

Picked up 2nd new board, install and same thing completely dead.
No instruction with board, but none were needed on previous jobs, pretty easy repair.

Reinstall original part, box started working.
Customer called this AM and said lights on but not cooling.

Any one had problems with this power board. Thanks in advance