0 votes
263 views

Not spining

0 votes
597 views

Older upright freezer runs but doesn’t cool.

  • nstaker asked 2 years ago
  • last active 2 years ago
0 votes
1k views

My fridge is not cooling, Hovers around 45-50 degrees. Originally it had icing problems in the freezer side when it started to go bad but that part was fixed. Freezer does hold at around 0 degrees. There is small amount of cool air coming through vent between freezer and fridge on top.

  • dragonkx asked 5 years ago
  • last active 5 years ago
0 votes
2k views

I have a gas range that was flagged by the gas company CO levels to high. I have a detector but didn’t bring it with me ( I was informed it was a gas leak and just brought my sniffer) Visual inspection showed a normal blue flame in oven .It is in a small apartment with no vent and the gas company didn’t leave any ppm #s .what should I be looking for to feel confident it’s not the oven just the size of apartment and no ventilation?

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
1k views

Water slowly leaks into the dishwasher when it is off. So the bottom of the dishwasher has a pool of water if not in use. There was sediment in the water valve, so I replaced the water valve… but the dishwasher is still leaking slowly while off. What could cause this issue?

0 votes
2k views
0 votes
3k views

The unit will agitate and drains but it will not go in to spin
Please advise

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
3k views

Checked polarity on outlet, check fuse, checked push start switch all good. There’s no power to the start switch. Only place I have power is on the line feed to timer. I’m thinking a bad timer but unsure

  • bean8066 asked 6 years ago
  • last active 6 years ago
1 vote
2k views

During agitation shifter doesn’t work and inner tub and agitator turn at same time.What is shifter voltage and resistance ? The inverter on the motor supply it’s voltage but what timer signal calls for it to actuate? Could my timer be bad or the motor or the shifter. Can you send me a theory of operation ?

  • cato91891 asked 6 years ago
  • last active 6 years ago
0 votes
2k views

The washer will still overflow after replacing the pressure switch and hose. We double check to ensure that the hose is cleared as well. It will also only overflow on the rinse cycle. During the fill cycle it will fill to the proper level and then once it is stopped and turned to the rinse cycle it will not drain out first. We have also tried replacing the timer as well with the same issue.

1 vote
2k views

Do you have the service manual for rvm5160dh1ww- is a hotpoint and for jvm7195df1bb- is a GE? The ge comes one but does not heat. How do I eliminate the control board from the magnetron and magnetron thermostat?

  • lue asked 6 years ago
  • last active 6 years ago
0 votes
8k views

THE HOTPOINT MICROWAVE DOEN NOT OPERATE BECAUSE THE THERMOSTAT AT LOCATION#: 138 ON THE DIAGRAM DOES NOT HAVE CONTINUITY. THE PART# IS WB27X11213 110/0.
THE MARKINGS ON IT IS KSD210 AND 70.
IS KSD201 THE GENERIC PART NUMBER, IF SO WHAT DOES THE 70 MEAN?
IS IT’S ROLE TO PROTECT THE MAGNETRON?
I NOTICED LOCATION# 117, PART#: WB27X11208 70/0 AND LOCATION# 138, PART# WB27X11212 120/0 AND LOCATION# 130 AND LOCATION# 130, PART#: WB27X11210 160/0 ARE ALL GOOD. IF THE 70 IS A TOLERANCE LEVEL, COULD THIS HAVE BEEN WRONGFULLY MIXED UP WITH LOCATION 117 THAT HAS A 70/0 NOT LOCATION 138 THAT HAS 110/0? DOES IT MAKE THAT MUCH OF A DIFFERENCE? IF I REPLACE THE THERMOSTAT THAT IS BLOWN AT 138 WITH A HIGHER NUMBER, FOR INSTANCE, 110/0 INSTEAD OF 70, MIGHT IT DELAY BLOWING, THEREBY DAMAGING THE MAGNETRON?

  • lue asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Problem with a Hotpoint Refrigerator

0 votes
2k views

My defrost heater is not testing out properly.

0 votes
2k views

My Hotpoint washer will not agitate or spin.

0 votes
2k views

My customer’s Hotpoint Refrigerator is having some issues. Not producing ice

0 votes
3k views

I replace the main control board, defrost thermostat, and defrost heater and still have the problem.

  • lopez1974 asked 7 years ago
  • last active 7 years ago
0 votes
2k views

I see that the belt is broken.
however when I push the start button it will only run as long as I holding it down .
the door switch is good.
but I’d I let go of the the start button it stops running

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

The top burners light no problem the pilot stay lit however in the oven the pilot will not light I have turn the thermostat on no gas is flowing through the burner

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

the customer says that the oven will go on by itself from time to time and the go off.
what can it be?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My Hotpoint dryer is making a loud squeaking noise.

0 votes
2k views

the customer is saying that the oven will go on by itself from time to time

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My Hotpoint dryer is making a loud high pitched squeaking noise.

Showing 1 - 30 of 53 results