0 votes
8k views

THE HOTPOINT MICROWAVE DOEN NOT OPERATE BECAUSE THE THERMOSTAT AT LOCATION#: 138 ON THE DIAGRAM DOES NOT HAVE CONTINUITY. THE PART# IS WB27X11213 110/0.
THE MARKINGS ON IT IS KSD210 AND 70.
IS KSD201 THE GENERIC PART NUMBER, IF SO WHAT DOES THE 70 MEAN?
IS IT’S ROLE TO PROTECT THE MAGNETRON?
I NOTICED LOCATION# 117, PART#: WB27X11208 70/0 AND LOCATION# 138, PART# WB27X11212 120/0 AND LOCATION# 130 AND LOCATION# 130, PART#: WB27X11210 160/0 ARE ALL GOOD. IF THE 70 IS A TOLERANCE LEVEL, COULD THIS HAVE BEEN WRONGFULLY MIXED UP WITH LOCATION 117 THAT HAS A 70/0 NOT LOCATION 138 THAT HAS 110/0? DOES IT MAKE THAT MUCH OF A DIFFERENCE? IF I REPLACE THE THERMOSTAT THAT IS BLOWN AT 138 WITH A HIGHER NUMBER, FOR INSTANCE, 110/0 INSTEAD OF 70, MIGHT IT DELAY BLOWING, THEREBY DAMAGING THE MAGNETRON?

  • lue asked 6 years ago
  • last active 6 years ago
0 votes
5k views

hotpoint oven the oven and broiler not working

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
4k views

Hi!
The problem is the following:
1. After turning on of a refrigerator, it works for ~2 hours, temp. goes down to -20 and +5 in freezer and cooling chamber, compressor stops
2. Then, after 10-15 minutes, it tries to start for 8-10 seconds, producing loud clicks and then stops. Freezer fan is working all the time.
3. Temp. goes up to +10 in both cameras, producing A1 or A2 alert.
If I give him a rest for 4-5 hours, this cycle repeats.
But some times (I don’t know why) this scheme breaks – compressor works (normally?), but temp. in cooling chamber rises up +10, meanwhile temp. in freezer drops to -26-27.
Thus, there is strange behavior – sometimes it seems to make vacuum in freezer, after the door is closed.

  • Anton asked 9 years ago
  • last active 9 years ago
0 votes
3k views

hotpoint side by side fridge inside lights working compressure hot condenser fan not running either is evaporator fan if compressure not working properly should the condenser fan still turn on not sure what to do next

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

The unit will agitate and drains but it will not go in to spin
Please advise

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
3k views

Checked polarity on outlet, check fuse, checked push start switch all good. There’s no power to the start switch. Only place I have power is on the line feed to timer. I’m thinking a bad timer but unsure

  • bean8066 asked 6 years ago
  • last active 6 years ago
0 votes
3k views

I replace the main control board, defrost thermostat, and defrost heater and still have the problem.

  • lopez1974 asked 7 years ago
  • last active 7 years ago
0 votes
3k views

The back left burner on my Hotpoint stove is not working.

0 votes
3k views
  • terrell asked 9 years ago
  • last active 9 years ago
0 votes
2k views

My microwave is making a grinding sound, and I’ve replaced the turntable motor, but the noise has not gone away.

  • Deann Russell asked 10 years ago
  • last active 10 years ago
0 votes
2k views

at first neither fan condenser or evap fan not working replaced condenser motor now works but evaporater fan not running be odd both fans failed at same time how can I test evaporator fan I replaced condenser now works do you think its computer board or bad evaporater

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Figured out the knobs are broken but not sure how to replace the start one. Couldn’t find a video to do it myself.

  • Willy T. asked 9 years ago
  • last active 9 years ago
0 votes
2k views

My Hotpoint dishwasher randomly shuts off.

0 votes
2k views

It’s gas by the way. What part would I need?

  • Tyler A asked 9 years ago
  • last active 9 years ago
0 votes
2k views

There is ice building up in the back of my Hotpoint freezer.

1 vote
2k views

Do you have the service manual for rvm5160dh1ww- is a hotpoint and for jvm7195df1bb- is a GE? The ge comes one but does not heat. How do I eliminate the control board from the magnetron and magnetron thermostat?

  • lue asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Hotpoint Dishwasher . Unit does not pump out all water at end of cycle. Unit pumps out all water in previous pump out, but not the last one. Solenoid for pumping water out engages, but the motor does not run, no power to motor. Since the drain solenoid activates and the motor doesn’t run at the end of the cycle, I suspect the timer is bad. Has anyone else seen this problem?

0 votes
2k views

the customer says that the oven will go on by itself from time to time and the go off.
what can it be?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My Hotpoint dryer is making a loud squeaking noise.

0 votes
2k views

GOOD MORNING. I DID NOT CHECK THIS FRIDGE YET. I AM BEING TOLD THAT THE FRIDGE TEMP IS FINE, BUT THE FREEZER IS NOT. ALSO, THE ITEMS IN THE FRIDGE VEGIE STORAGE DRAW ARE FREEZING. I NEVER WORKED ON A HOTPOINT BEFORE, BUT THIS SOUNDS BACKWORDS. ANY HELP WOULD BE GREATLY APPRECIATED. THANKS, TODD FROM NY.

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

During agitation shifter doesn’t work and inner tub and agitator turn at same time.What is shifter voltage and resistance ? The inverter on the motor supply it’s voltage but what timer signal calls for it to actuate? Could my timer be bad or the motor or the shifter. Can you send me a theory of operation ?

  • cato91891 asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Problem with a Hotpoint Refrigerator

0 votes
2k views
0 votes
2k views

The element on my Hotpoint stove is not heating, also the clock is not working.

0 votes
2k views

My Hotpoint refrigerator is not getting cold enough.

0 votes
2k views

I have a gas range that was flagged by the gas company CO levels to high. I have a detector but didn’t bring it with me ( I was informed it was a gas leak and just brought my sniffer) Visual inspection showed a normal blue flame in oven .It is in a small apartment with no vent and the gas company didn’t leave any ppm #s .what should I be looking for to feel confident it’s not the oven just the size of apartment and no ventilation?

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
2k views

The ice shoot is not closing properly on my Hotpoint refrigerator.

0 votes
2k views
0 votes
2k views

My Hotpoint refrigerator is not getting as cold as it should.

Showing 1 - 30 of 53 results