0 votes
3k views

The burner and infinite switch part number is w10823734. The espy sensor harness on the old and new sensors won’t work on the new INF SWitch . or would it be simpler to use the old burner with the 12002121 INF SWITCH?

I need a wiring diagram. And any help you can give.

  • Pancakes asked 5 years ago
  • last active 5 years ago
0 votes
2k views

can set clock for 1 min cook or 5 min cook magnetron wont kick on until 45 second run time help

  • joey candelaria asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Customer said one time no burners would come on when set. Now the right front won’t boil water. Could this be a bad appliance manager board? Both duel elements work. Even on number 10 setting it will go off with a pan of water on it. Any advice welcome.

  • Pancakes asked 6 years ago
  • last active 6 years ago
1 vote
2k views

Then after a day or week it comes back on with time and we can use the oven again. And stays on for another day or two – then goes black out.
I tried rebooting it by shutting circuit off for a minute & the turning back on.
Display unit was replaced by dealer 3 years ago.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

I have a 48″ Jenn-air range ; that main oven flame was sputtering and shut off. I started smelling gas and called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

0 votes
3k views

Do you have a video on how you replace the bake element on this double oven. I also like to know if you have a diagnosis sheet or cheat sheet that I can put the unit into diagnostic mode? I don’t have anything on this oven except a schematic. Takes a long time to get to preset temperature 30 min.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

I am not getting any display option. And it’s causing the unit not to cool. It is not on Sabbath mode and I am getting power to the display.. What else can I look for

  • Guest asked 8 years ago
  • last active 7 years ago
0 votes
2k views

I need to remove the icemaker. do you have a video>

  • burtyost asked 7 years ago
  • last active 7 years ago
0 votes
26k views

I repaired the drain pump on my dishwasher. Now I can’t get it to start.

  • Paul Bergstrom asked 10 years ago
  • last active 10 years ago
0 votes
2k views

RIGHT FRONT BURNER NOT WORKING; BURNER IS DISCONTINUED BUT IF YOU ORDER SWITCH IT COMES WITH BURNER AND WIRING HARNESS. PART # W10823734. THIS IS NOT THE USUAL INFINITE SWITCH LIKE THE REST OF THE BURNERS. IT LOOKS LIKE THE ONE IN THE KIT BUT EPIC SENSOR NOT HOOKING UP. AM I DOING SOMETHING WRONG.

  • joeski1369 asked 4 years ago
  • last active 4 years ago
0 votes
2k views

All buttons work on the microwave but programmed to start the machine the timer just clicks down and the turntable does not turn

  • pixey smith asked 9 years ago
  • last active 9 years ago
0 votes
2k views

The lights on the control panel on my Jennair stove will not come on.

0 votes
2k views

Are you able to get me the part number to the entire cartridge, including burners and all, where all I have to do is swap them out and not rebuild the entire thing?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1k views

I would like to know how to remove the mounting screw on the bottom of the unit. Do we have to remove the front door out? Would you let us know? The bottom screws are blocked with front door hinge , and not able to access the screw to be out. Thank you.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
10k views

I would like to know what this error code means and what can I do to fix it?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

My Jenn-Air dishwasher is not draining properly

Showing 1 - 30 of 208 results