I repaired the drain pump on my dishwasher. Now I can’t get it to start.
- Paul Bergstrom asked 10 years ago
- last active 10 years ago
The gravy went down the valve stem hole onto one of the Valve Switches. (The orange colored square switch can be seen looking down the valve stem). Could this short out that one valve switch and cause ALL burners to spark ignition when the unit is plugged in? If so, what is the procedure to disassemble the unit to replace that valve switch. Also, could that gravy spill have caused damage to the Spark Module? If so, where is it located on the model?
- Bill Gale asked 10 years ago
- last active 10 years ago
Some of the buttons on the touch pad work, and others don’t. Is this a faulty front touch pad or the control board behind it? Was thinking about giving it a go myself if possible.
- Justin asked 9 years ago
- last active 9 years ago
Wasn’t sure if there was a problem with a part or maybe something stuck? Having my husband take a look but not sure where he should start.
- Lorraine asked 9 years ago
- last active 9 years ago
I seem to be getting a build up of suds, they are not all getting rinsed out with each load ran.
- Alvin asked 9 years ago
- last active 9 years ago
I have installed three sets of door hinges. I know these hinges don;’t work because I have run into a few of these stoves.
Has anyone heard of a solution to this? Whirlpool has to know about it because I had my parts supplier inquire a year ago. I had one customer that was ok with a latch on the side of his stove. Any suggestions ?
Thanks,
- T&G Appliance Repair asked 9 years ago
- last active 9 years ago
I have a a 48″ Jenn-air range ; customer complain that main oven flame was sputtering and shut off. They started smelling gas he called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?
- T&G Appliance Repair asked 9 years ago
- last active 9 years ago
Control board and touch assembly replaced last month . Now the range shuts off after 3 min. in self clean. Thanks in advance for your response.
- James Buchanan asked 9 years ago
- last active 9 years ago
I have a 48″ Jenn-air range ; that main oven flame was sputtering and shut off. I started smelling gas and called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?
- Harley Clark asked 9 years ago
- last active 9 years ago
I have a customer that states he has to change the filter in this refrigerator every 4 weeks. New filter goes in and the water flows well from dispenser but at about four weeks the flow slows to almost nothing again. This pattern has been repeat over and over. The customer states this is averaging out to a $1.75 per day. Would this be a problem with hard water? Has anyone else had this problem? I was wondering if I should install some sort of a prefilter. Any suggestions would be appreciated. Thanks
- T&G Appliance Repair asked 9 years ago
- last active 9 years ago
When customer programs MW say for 60 seconds, it starts counting down 59 58 57 56 55 . When that happens, it quits heating and shuts off. He will cancel, and after a few seconds of heating and counting down, it stops heating and the count down just stays there.
- Fred Abernethy asked 9 years ago
- last active 9 years ago
I don’t have a model number on this oven. I was working in this kitchen removed the oven door improperly and could not reinstall it. I pushed the hinges and set the catches and attempted to put the door back on. After a little effort I got it back on but then could not open it. The door is locked. I have tried a coat hanger to pull on the lock without success. I have tried setting self clean and then cancelling it and turning off the circuit breaker for a few minutes. I would be very greatful for any tips on how to get the door open. Thanks
—
- T&G Appliance Repair asked 9 years ago
- last active 9 years ago
We have a Jenn-air oven/mw combo. Microwave starts counting down and then stops running and heating after 5 seconds. It starts counting for example 60-59-58-57-56-55-55-55-55-55-55-55-55. Never come across this before but assume it could be sensing an overheat and shutting off?
- Harley Clark asked 9 years ago
- last active 9 years ago
My top rack falls down if I get more than 5lbs on it ? Has anyone else had this issue.
- Gary Williams asked 9 years ago
- last active 9 years ago
The front right burner on my Jenn-air cooktop is not working
- Fred Abernethy asked 8 years ago
- last active 8 years ago
The lights on the control panel on my Jennair stove will not come on.
- Fred Abernethy asked 8 years ago
- last active 8 years ago
I would like to know what this error code means and what can I do to fix it?
- Guest asked 8 years ago
- last active 8 years ago
We have a Jenn-Air/Maytag Appliances JDS9860AAP oven, which displays an F1 error code not long after reaching a preheat temp (typically 350). After clearing the error, it eventually comes back multiple times as the oven cools and has to be cleared each time as it cools its way down.
- Guest asked 8 years ago
- last active 8 years ago
This unit has a infinite switch, I don’t know if it has a thermostat to regulate the temperature or is it all done by the infinite switch. What regulates the temperature?
- Guest asked 8 years ago
- last active 8 years ago
I replaced the door hinges on the oven about 4 weeks ago. Door was not closing all the way. New hinges worked great until a call back yesterday. This is not the first Jenn Air oven I have had this issue with. . Thank you for any advice.
- Gary Williams asked 8 years ago
- last active 8 years ago
I looked at this dishwasher yesterday. . Complaint: Dishes not getting clean anymore like they use to and food is left on the dishes. I stripped the dishwasher down and checked the impeller, made sure all the spray arms were clear, and sump was clean. Unit was very clean with little to no debris. Tested the unit and it appears all spray arms are turning and upside down cups in the top rack are quickly filling with water. Water is hot. Good wash action. I did find that the turbidity sensor failed twice in diagnostics but then made it through the test two other times.I did not ohm it out. Heating element is getting hot. If the turbidity sensor is failing, would this affect performance or make changes such as shortening or eliminating wash cycles? Would changing the turbidity sensor be the best course of action? Thank you for any advice.
- Fred Abernethy asked 8 years ago
- last active 8 years ago
I need to remove glass top on cooktop were are the screws I need to ge to too take apart
- Guest asked 8 years ago
- last active 8 years ago
Center burner one element like grittle. What is happening two separate infinity switches. If you turn on either one of the burner it will blow the 40 amp breaker.
- Guest asked 8 years ago
- last active 8 years ago
Do you have a video on how you replace the bake element on this double oven. I also like to know if you have a diagnosis sheet or cheat sheet that I can put the unit into diagnostic mode? I don’t have anything on this oven except a schematic. Takes a long time to get to preset temperature 30 min.
- Guest asked 8 years ago
- last active 8 years ago
This is a double wall oven and only the top one is malfunctioning. The unit shuts off after 5 seconds of being turned on bake and the control board looks a bit stange. Could there be anything else other than the control board going wrong with this unit?
- mytechjoe asked 8 years ago
- last active 8 years ago
I am not getting any display option. And it’s causing the unit not to cool. It is not on Sabbath mode and I am getting power to the display.. What else can I look for
- Guest asked 8 years ago
- last active 8 years ago
GOOD MORNING, I DID NOT GO ON THE CALL, BUT I AM TOLD THAT THE UNIT IS NOT WORKING AND IS MAKING A GROANING NOISE. ANY INFO WOULD BE GREAT, AS I HAVE NEVER WORKED ON A JENN AIR DISHWASHER. THANKS, TODD FROM NY.
- Guest asked 8 years ago
- last active 8 years ago