Brand: Jenn-Air

I repaired the drain pump on my dishwasher. Now I can’t get it to start.

Oven light turns on by itself , how can I prevent this from happening?

This code says cooling fan speed too low or won’t come on. Do you have a video on this one and a service manual and any tips?

We have a Jenn-Air/Maytag Appliances JDS9860AAP oven, which displays an F1 error code not long after reaching a preheat temp (typically 350). After clearing the error, it eventually comes back multiple times as the oven cools and has to be cleared each time as it cools its way down.

I would like to know what this error code means and what can I do to fix it?

I replaced the door hinges on the oven about 4 weeks ago. Door was not closing all the way. New hinges worked great until a call back yesterday. This is not the first Jenn Air oven I have had this issue with. . Thank you for any advice.

I have a 48″ Jenn-air range ; that main oven flame was sputtering and shut off. I started smelling gas and called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

ice maker w10377151 has been converted to icemaker W10882923 unclear instructions on how to convert

I am not getting any display option. And it’s causing the unit not to cool. It is not on Sabbath mode and I am getting power to the display.. What else can I look for

I have a a 48″ Jenn-air range ; customer complain that main oven flame was sputtering and shut off. They started smelling gas he called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

The burner and infinite switch part number is w10823734. The espy sensor harness on the old and new sensors won’t work on the new INF SWitch . or would it be simpler to use the old burner with the 12002121 INF SWITCH?

I need a wiring diagram. And any help you can give.

The unit will start to heat and then I get the error code f8e0 underspeed fan.
I do hear and feel the fan blowing.
Please advise

My Jenn-Air dishwasher is not draining properly

I have a customer that states he has to change the filter in this refrigerator every 4 weeks. New filter goes in and the water flows well from dispenser but at about four weeks the flow slows to almost nothing again. This pattern has been repeat over and over. The customer states this is averaging out to a $1.75 per day. Would this be a problem with hard water? Has anyone else had this problem? I was wondering if I should install some sort of a prefilter. Any suggestions would be appreciated. Thanks

Do you have a video on how you replace the bake element on this double oven. I also like to know if you have a diagnosis sheet or cheat sheet that I can put the unit into diagnostic mode? I don’t have anything on this oven except a schematic. Takes a long time to get to preset temperature 30 min.

Are you able to get me the part number to the entire cartridge, including burners and all, where all I have to do is swap them out and not rebuild the entire thing?

I looked at this dishwasher yesterday. . Complaint: Dishes not getting clean anymore like they use to and food is left on the dishes. I stripped the dishwasher down and checked the impeller, made sure all the spray arms were clear, and sump was clean. Unit was very clean with little to no debris. Tested the unit and it appears all spray arms are turning and upside down cups in the top rack are quickly filling with water. Water is hot. Good wash action. I did find that the turbidity sensor failed twice in diagnostics but then made it through the test two other times.I did not ohm it out. Heating element is getting hot. If the turbidity sensor is failing, would this affect performance or make changes such as shortening or eliminating wash cycles? Would changing the turbidity sensor be the best course of action? Thank you for any advice.

This unit has a infinite switch, I don’t know if it has a thermostat to regulate the temperature or is it all done by the infinite switch. What regulates the temperature?

the water valve is in the fresh food compartment. how to replace it.

I have installed three sets of door hinges. I know these hinges don;’t work because I have run into a few of these stoves.
Has anyone heard of a solution to this? Whirlpool has to know about it because I had my parts supplier inquire a year ago. I had one customer that was ok with a latch on the side of his stove. Any suggestions ?
Thanks,

When customer programs MW say for 60 seconds, it starts counting down 59 58 57 56 55 . When that happens, it quits heating and shuts off. He will cancel, and after a few seconds of heating and counting down, it stops heating and the count down just stays there.

The lights on the control panel on my Jennair stove will not come on.

only three of the burners will ignite.
the other one I see the spark but it’s very low and all the other burners click wehn I try to ignite it

The gravy went down the valve stem hole onto one of the Valve Switches. (The orange colored square switch can be seen looking down the valve stem). Could this short out that one valve switch and cause ALL burners to spark ignition when the unit is plugged in? If so, what is the procedure to disassemble the unit to replace that valve switch. Also, could that gravy spill have caused damage to the Spark Module? If so, where is it located on the model?

We have a Jenn-air oven/mw combo. Microwave starts counting down and then stops running and heating after 5 seconds. It starts counting for example 60-59-58-57-56-55-55-55-55-55-55-55-55. Never come across this before but assume it could be sensing an overheat and shutting off?

I need to remove glass top on cooktop were are the screws I need to ge to too take apart