Brand: Kenmore

My dryer powers up, but when I press the button to start a cycle, it just clicks and stops completely.

I watched your video (http://www.youtube.com/watch?v=jIdtNdDXFDk) and have this identical issue. I want to get the replacement tube shown in the video, so I called your parts department. After explaining my dilemma, I thought I got the right part, but after placing the order and looking at the part number provided – IT IS THE SAME AS WHAT I HAVE. Please advise as to how to order the replacement tube shown in your video.

I have a Kenmore Coldspot 52582201
The ice maker and water dispensers are dispensing slimy ice and gross slimy stuff in the water.
I change the filter regularly.
I love this refer. and don’t want to have to get rid of it.
Please help me

stops in the middle of the heating cycle

looking for the C Clip that holds the brake cam driver.
I have tried to find it in different appliance stores

Hi, We have ice that builds up in the bottom of the freezer in our Kenmore Cold Spot side-by-side refrigerator/freezer. I break it up and clean it out and within a couple days, it’s back. I’m not sure what is causing it or how to fix it. I’ve seen many posts online but none are specific to my model….just want to make sure we do the right thing to fix it. Thanks in advance for any guidance you can give me.

Amy

where do I find a wire diagram or a video that shows the wire connections to the thermostat and cut offsensors on a Kenmore elite dryer model 11063012101.

I’m a marone member trying to use your web sight apparently we do not get premium videos unit does not go in to spin kenmore washer washes drains but no spin then sd code and f51

My Kenmore side by side fridge #10650532101 is not cooling. The relay switch has been replaced and the unit turns off and on. I viewed an online diagnostic video and I struck(tapped) the thermostat and the unit began to cool. Does this mean that my thermostat is not functioning and needs to be replaced? Or could it be something else? Please help.

We have to keep pushing the start button on our Kenmore Ultrawash Quiet Guard Standard dishwasher from 4-6 times before it keeps running. When you first start it, it will fill (it starts and run for less than 30 seconds). When the fill stops and it’s ready to go to the next thing, it stops and all of the lights on the control panel go out. We push start again and it will run for another few seconds, then the lights go out again. This process repeats several times. After pushing start for the initial time and then again 4-5 times, it will finally continue to run and successfully complete the cycle. Can you offer any guidance for this? This dishwasher is only a couple of years old… no more than 3.

Thank you for any help you can offer.

Tracy Monroe
Corydon, Indiana

I have a Kenmore washer that the unit is not spinning and the clothes are sopping wet; but there is no standing water inside the tub. It sounds like it is in a spin mode but it is not spinning. I have checked the motor coupler and it appears to be fine… nothing is cracked or stripped… it seems to be in good condition. I have also checked the water hoses attached to the water pump and there is no blockage. What other conditions would cause the unit to not spin??? Would a possible transmission issue be next to check??? The unit sounds like it wants to work but nothing appears to spin; and the fabric softener is not dispensing during usage.

Thank you for any help –

Fred in Lubbock, TX

My husband is determined to replace the belt on our washer himself, but I couldn’t find a video matching our model. Any help you can give would be appreciated.

I have a washer that is testing my patience. Originally it wasn’t spinning out and I noticed the lid latch seemed loose, so I assumed it was the problem. Replaced it and same issue. Read on another website it could be the board, so I did that. Same thing. Anyone on here think of what else I could get my hands on to check? Really don’t want to have to buy a new one.

My Controls appear to work normally, but drum doesn’t rotate. On initial Diagnostic test, when I press power btn, I get the Code 08, I’ve tested the Thermal Fuse, it’s OK.

I’m suspicious of Broken Belt switch, as it doesn’t click when I depress lever.

If the Code 08 doesn’t mean anything, I plan to continue with motor control test.

Thanks, Bill

I am trying to release the transmission from the unit to further look at possible tub not spinning problems. I have seen where you have to release the internal screw from at the bottom of the dispenser that helps to hold the transmission shaft. The screw head is stripped; and I am assuming that someone else has been into the unit. Is there a way of getting the screw off; or the plastic agitator shaft completely out of the way so I can continue at removing the transmission/basket drive from the bottom.

Thanks… Fred in Lubbock. TX

The washer fills and stops. Replaced lid switch that wasnt the problem

i was told that my thermostat needed to be replaced do you have tech in the oakland ca area and a number for their local office? id try to replace it my self but i dont want to cause anything else to go wrong. thank you for ur time.

My dryer seems to heating fine but the drum is not turning. How would I go about fixing this?

My washing machine seems to just quit working before spinning my clothes dry. I can normally restart it but now it just won’t do anything after washing and draining. Would greatly appreciate some help in figuring out what is causing this to happen. Could my husband do the repair or would it be too complicated? I’m never sure on what to do when it comes to our appliances and whether we should just get a new one.

This is a he machine and unfortunately I used some regular liquid tide detergent. I’ve since ran several cycles with no detergent, he bleach on self clean mode and cleaned the machine with he cleaner. I’ve also ran the diagnostic test and it won’t go past c7. It drains all the water and then tries to agitate for about 10 minutes and then starts to fill back up with water. It does not go past c7 on the diagnostic test. Can this be fixed?

My washer won’t spin my clothes out enough, they are sopping wet still. I replaced the lid latch thinking it was that from a video I saw, and then was told it may be my control board from someone else, so I’ve done that as well. Really frustrated now, what else do I need to do?

I at first thought that the ice dispenser motor was the problem, so I have replaced it with a new drive motor. However neither the new motor or the old motor turn on when I push on the ice dispenser paddle. So I am now thinking that the problem is in the control panel switches or ????
Just looking for some other ideas and help.

Thanks
Robert Christensen
208-436-6213
rob@cmi80.com