Brand: KitchenAid

Hi –

My kitchenaid dishwasher (3 years old) is leaking water under the right bottom side of the door. It is not a lot of water, and my first attempt to fix it was cleaning the seal, which had some small amount of scum on it. This fixed it temporarily, but a few days later the water leak was back. It is not a lot of water, and doesn’t happen during the rinse only cycle, apparently. Any ideas/thoughts on this would be very useful. It is a stainless steel kitchenaid dishwasher, similar to model KDTE104DSS.

Thanks!

Adam

it just happened one day with no prior problems. only the cancel light will illuminate when pressed. tried turning off power for over 12 hours still the same. then after a week it worked as normal just once now back to just the cancel.

My top oven will not heat. When I put it on self clean the top burner inside the oven lights up and then begins the self clean. However when I go to heat something up on say 400 degrees, it does nothing…..very strange what is going on? It is obviously getting gas, but when I go to bake with the top oven it will not work.

Now the bottom oven is working, but we rarely have used it. Is this a flaw with Kitchenaid. The oven is only about 2 years old.
Thanks for the help!
Ryan

My fridge started a double beeping noise. At the same time the freezer and refg temps rose. I cleaned the coils in front bottom and fan by compressor. The temps are running @ 14* in freezer and 44* on refg. I tried turning off the cooling system and restarted after 2 minutes but no change in temps. I watched your video on changing the compressor kick starter. Not sure what to do. The fridge is 7 – 8 years old. Can you give me some advise?
Thanks, Lynn

Been having a problem that the freezer and refer not reaching set temps. This morning when it was quiet I could hear the fan motor cycling. Run for 10 seconds then off for 1 or 2 seconds and then back on again over and over.

Having troubles getting my kitchen aid dishwasher to start model number KUD01ILBL6 I rebooted it by pushing scrub and energy button x5 alternating waiting and then push cancel button 1 x and no success. Is this the correct rebooting technique for this dishwasher, and what else can I do????

i have a icemaker problem,
my icemaker stopped making ice about 2 weeks ago and i need help, i took it out clean it and re installed it
but that did not help the red light is flashing and no ice. i dont want to buy a new icemaker and after still have the same issue.
please can you guys help
thank you
artie

My dishwasher has power and when I push the normal cycle button and then start, the lights come on, but after a few seconds they just turn off and it never starts. Do you think it could be the fuse?

Hello!
Thanks to your video, I was able to diagnose the cause of my leaking bottom drawer freezer, order the right part, and replace the sticky (disgusting!) duck bill grommet with the P-trap. When I was finished I tapped out the almost two inch thick glacier that had formed on the bottom of my freezer and thought we were good to go – but when I checked the freezer the other day there was ice on the bottom again!!

I gather this means that somewhere between the bottom of the fridge and the entry to the P trap there must be an ice dam. What is the best and/or easiest way to melt that out? I don’t have access to any of the fancy tools but I do have a hair dryer and screwdrivers and lots of spunk so hoping those will do the trick.

Thank you so much for your free videos, they are the best. I never would have felt empowered to fix this thing all on my own without your help.

Kindly,
Katie

Every time I baked three or four trays of pastries I have this problem. The heat would not go up on the the third or fourth one. Every thing else is working. I baked one at a time.
Please let me know the problem.
Thank you.
Barlen

light in the oven is always on , the turn off key seems is not working and as well some other 2 o 3 keys. my guess is i need to change the membrane, but , how i will konw if is just the membrane and not the the coen ntrol too. there is not teck sheet in the oven or else where. i do not want to give a wrong estimate to my costumer because the control is too expensive, one of the control is $279.17 and the membrane $140.00 if i added together both is so much. menbrane pt# 9756595bt- control pt# 9762812

Looking for an idea of why this unit is failing again. This will be the fourth repair on this in two years, and KitchenAid has been useless. Main board has been replaced once, rebuilt once, something about the defroster has been replaced, and the freezer is not working. Again.

Can you tell me how to navigate the menus for diagnostics?

Any help appreciated.

Hd & Normal button lights are flashing alternating. Turned breaker on last nite , closed door & it pumped out. Then nothing. Does not run. no response from machine.

My dishwasher will not start. The lights light up when I choose different functions but it won’t actually start when I press Start. I tried the reset by pushing the High Temp Scrub and Energy Save Dry buttons alternating five times each and the unit will go through the reset. It also drains when I press cancel after resetting. I am not sure how to proceed.

TRIED TO CHECK BAKE ELEMENT. CUSTOMER SAID NOT BAKING GOOD OR GOING INTO SELF CLEANING. HOW TO GET TO IT?

I HAVE A CUSTOMER WITH THIS KITCHENAID DISHWASHER WHERE THERE ARE THREE LIGHTS LIT UP ON THE PANEL WHEN POWER IS SUPPLIED WITH NO RESPONSE TO OPERATOR INPUT OTHER THAN THE OPTIONS BUTTONS. REPLACING THE TOUCH MEMBRANE- PART # W10077793 RESULTED IN THE SAME THREE LIGHTS BEING LIT WITH ONE ADDITIONAL-HEAVY WASH, AND NO RESPONSE TO OPERATOR INPUT. WAS WONDERING IF THE CONTROL BOARD, RIBBON OR INTERCONNECT COULD BE AT FAULT. HAVE NEVER SEEN A CONTROL BOARD AT FAULT FOR THIS PROBLEM BEFORE. HAVE ALWAYS SOLVED THIS PROBLEM AT LEAST TWENTY TIMES BEFORE BY REPLACING THE TOUCH PANEL. THE RIBBON AND INTERCONNECT LOOK LIKE STRAIGHT DATA TRANSFER TO ME.

Unit is about 3 years old and has had lots of use. Tonight, it was making an intermittent beeping noise and I asked my wife what it was. She said it was the washer and went over to it and pushed a button. Don’t know which one but it had filled and ran and I think may have been drying at the time. At any rate, she then tried to restart it and no lights were coming on at all. I went to the main fuse panel and shut down the electricity for about 30 seconds and then turned it back on. She shut the door on the machine and tried again, the light came on as if it was going to run but then about a minute or so later shut off and no light or lights again. Thank you for any help you can be.
Sincerely.
John

I have this gass stove , kitchenAid Model # KGRI801PBS00.
Costumer complaint: make short circuit , tripeed braker (or blow out braker) at braker box , then He restore power and blower motor kept running all the time ( non stop).
I take off the touch panel with the control box behind the touch panel and restore power blower fan motor kept running , so, I hit with my screw driver the relay board , the one is located behind the surface and get the motor stop .
But when , I put back the touch pad with the control is at back the touch panel and press the bake , the braker at braker box when off again (braker tripped).
another interesting question that I have is: I take away the cables going to the motor and check those cables for ground it was grounded , when the plug is inserted in the wall outlet, but if , I take away the plug from the wall outlet , now is not grounded is that ok?.
Now I , think I have problems with one of the board ,but I don’t know , which control board or even if the touch panel .
How I will determine or probe each one of this control or touch panel. thank for your help, wating for your answer, my email address is : armandoappliances@gmail.com , or also I have this other one : armgua@gmail.com. I am fan of yours wabesite and also I was refered to you, by marcone appliance which , we have accesd I belive as a premium till December 31.

Our dishwasher hasn’t been very effective, and I thought it was a bad chopper assembly, so I changed that out, but it’s still not working as well as I’d like. What else can I check?

Dishwasher won’t start. Panel lights work. I press (Normal Wash), (Heat Dry) and (Start/Resume).

1) I can hear water softly running.

2) After a minute or so, I hear a 1 second long buzz that repeats every 5 seconds for a half a minute or so.

3) Then the cancel/drain light comes on solid. And, water is draining into the garbage disposal.

4) After 30 seconds or so, all the lights go out.

I reset everything by shutting off the circuit breaker. No change.

I think maybe the Float mechanism or switch is bad, so I remove the float and everything is very clean and free. I remove the switch and check it with a meter and it is fine.

So, what do I do now? Could it be anything else other than the control board?

This dishwasher we have seems to only be cleaning the bottom rack, the top has a lot of leftover stuff left on the dishes. I checked hot water coming in, and even cleaned the spinners out from another video I saw on here. Now what?

The bottom drawer is not cooling and top drawer freeze up on back wall?

How do we replace the two tracks that hold the upper rack? Is there a video that shows this? Ours does not have visible screws. Please advise. If you have a video, we would definitely subscribe to watch that video.