0 votes
15k views

Hi –

My kitchenaid dishwasher (3 years old) is leaking water under the right bottom side of the door. It is not a lot of water, and my first attempt to fix it was cleaning the seal, which had some small amount of scum on it. This fixed it temporarily, but a few days later the water leak was back. It is not a lot of water, and doesn’t happen during the rinse only cycle, apparently. Any ideas/thoughts on this would be very useful. It is a stainless steel kitchenaid dishwasher, similar to model KDTE104DSS.

Thanks!

Adam

  • Adam asked 10 years ago
  • last active 8 years ago
0 votes
14k views

Seems like the main oven door is not contacting with the latch/light switch.

0 votes
13k views

I am working on a 4 door kitchenaid refrigerator that has icemaker in the celling in refrigerator side how do you get it out , dose anybody have a service manual to share whit me MOD#KFIS29PBMS02 and SER#K33307442 help is very appreciated

0 votes
8k views

Kitchenaid built in oven microwave combo KEMS308SSS00. Original call was for a F1E5 error inverter. Inspection of inverter the board was clearly burned in several areas. Replaced inverter board and main control board.

When powered back on got F0E6 lost communication error. Checked all fuses and wires between Appliance Manager Board and microwave user interface. Had to replace manager board. After replacement, F1E5 error came back.

What have I overlooked or done incorrect? I would like to get this running for the family. Thank you.

0 votes
8k views

Looking for an idea of why this unit is failing again. This will be the fourth repair on this in two years, and KitchenAid has been useless. Main board has been replaced once, rebuilt once, something about the defroster has been replaced, and the freezer is not working. Again.

Can you tell me how to navigate the menus for diagnostics?

Any help appreciated.

  • Paul asked 9 years ago
  • last active 8 years ago
0 votes
8k views

WE HAVE A MICROWAVE/WALL OVEN COMBO WITH A F6 E8 CODE. THAT CODE IS FOR THE MICROWAVE APPLIANCE MANAGER (iE CONTROL BOARD). CHECKED THE WIRE HARNESS TO THE DISPLAY BOARD, WHICH IS OK AND THEN REPLACED THE APPLIANCE MANAGER, STILL GET THE SAME CODE. THE ONLY OTHER THING LEFT IS THE MICROWAVE DISPLAY BOARD, WHICH IS NOT VERY COMMON AND TWICE AS EXPENSIVE. SEEING IF THERE ARE ANY SERVICE UPDATES FOR THIS PROBLEM.

THANKS

  • halco1242 asked 6 years ago
  • last active 6 years ago
0 votes
8k views

I have a Thermador built in refrigerator with a evaporator leak. The unit was built by Kitchen aid. I know the Kitchen Aid evaporator and heat exchanger are 1/2 to 1/3 the price of the Thermador parts. Does anyone know where I can find the Whirlpool part number for these parts or maybe get the equivilant model number.

Thanks
Mark Kelly
Kelly’s Appliance Center

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
7k views

Ref is not cooling, no lights in the fresh food compartment and has a PF code. Previous tech replaced control board and user interface and still the same.

0 votes
5k views

i have a kitchenaid french door refrigerator and the freezer is working fine but the refrigerator is freezing the food in refrigereator section

0 votes
5k views

Have a kitchenaid wall oven. Model KEBS107SSS04
Error code says to replace the ( UI ), I assume this means USER INTERFACE.
touch pad and pc display board. Neither are identified as a UI and both are costly.

0 votes
5k views

Hi my kitchenaid microwave went completely dead on me after the door mechanism got stuck. I was able to release it no problem and the door opens and closes perfectly but the unit is dead as can be. Checked the breaker and it’s A-Ok.

0 votes
5k views

(Brand selector not finding Viking)
Was beeping heating alarm on the panel replaced fresh food section temperature sensor that was $70 and the alarm went away but freezer and fridge still both extremely cold. Eggs and everything else get frozen in the fresh food section and freezer ice cream turns into a rock. I ordered the low-voltage board because that’s what controls the temperature should I have ordered something else as well?

0 votes
5k views

We took a power hit while we were on vacation and the unit is not working correctly now. It seems to be in “Sabbath” mode, but I can’t change it on the control panel.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
5k views

My name is Roland,
Question: I am working on a Kitchen Aid dual fuel gas range MD# KDRU7893VSS03 SN:DB1375935. The issue with this unit is there’s an error code which says NTC out of Range. I have tested all fuses in the back of this unit, I have changed the sensor -W1076760, the boiler assy -9758598, the appliance manager-w10339702. Still when power up, it goes into lock out with NTC out of range, call for service.
Can anyone help with this issue please. I await your response.
Roland

0 votes
5k views

I have a Kitchen Aid wall oven, electric heat. Model # KEBS107DAL4 – gives fault code:
F3 – E2 ( Oven too hot Replace oven temperature sensor)
This fault code only when self-cleaning. Bake and Broil works fine.
Wouldn’t the sensor fail for baking as well? Thanks in advance for any help.

0 votes
4k views

Need service manual so I can diagnose and know how to disassemble components to get to evaporator defrost issue. Thank you.

0 votes
4k views

Customer says that over 7 techs already visited him to try to solve freezer still warm issue.
There is no frost build up near evaporator coil. Heater, thermostat and fan inside freezer work.
customer says previous techs suspected a leak or sealed system failure. They changed compressor, 3 way valve, control board in freezer and fresh food section fridge. But freezer still warm. If the compressor is new could they have missed the start relay before the compressor ? Does it always have to “click” before you determine it is bad ?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

The fresh food evaporator keeps frosting up. I have changed the control board and the evaporator thermistor and still keeps frosting up. I have run it through diagnostics and everything seems to be working fine. Any suggestions. I also would like to know what the resistance readings are on those thermistors.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
4k views

The door is not locked however I’m still getting this message.
It happened once before we unplugged it and it worked fine now however we unplug it we get the power failure message and then F5 E7

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
4k views

I had read, in the past, that the time the system takes to equalize can indicate the problem in the sealed system. Is this the case, and if so can you elaborate?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
4k views

Somebody already replaced the main control board and the power board but the error keeps coming back Can you guys pull me in the direction of a resolution and also can I get some diagnostic manual’s please

0 votes
4k views

KitchenAid dishwasher model KUDS30IXBL8 do you have parts list ?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
4k views

My dishwater is leaking water from somewhere.

0 votes
4k views

f3 e2 error when you use the micro I replaced the erc because there was no display now I get this code and I already checked sensor I was thinking about installing another erc

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
4k views

It seems that the only part number I see coming up for a p-trap drain kit is “W10619951”. In the video, it says there is a different kit for a fridge with 30″ doors, and ones with 33″-36″ doors. How do I know which part to get? I cannot find any place that clearly states which part number is for which size doors. Any help is appreciated. Thanks.

  • Scott Thomson asked 9 years ago
  • last active 9 years ago
0 votes
4k views

I’ve replaced a non working evap fan and it cools but not to the proper temp programmed.
Kitchenaid ksc24c8yy02

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
4k views
  • Phyllis asked 9 years ago
  • last active 9 years ago
0 votes
3k views

My kitchenaid washer is leaking and has a broken lid switch.

0 votes
3k views

My dishwasher will not start. The lights light up when I choose different functions but it won’t actually start when I press Start. I tried the reset by pushing the High Temp Scrub and Energy Save Dry buttons alternating five times each and the unit will go through the reset. It also drains when I press cancel after resetting. I am not sure how to proceed.

  • Ryen Mullen asked 9 years ago
  • last active 9 years ago
0 votes
3k views

I replaced the W10428901 control board an I am getting PE 000 code. I do not know the proper button to push to set the code. the code on the model tag is 13.

  • Guest asked 7 years ago
  • last active 7 years ago
Showing 1 - 30 of 383 results