Brand: Samsung

I watched replacing video and it was Excellent. I however don’t have a meter to check it after installing. So I tried powering up dryer after I was done and it kicked breaker right away. Trying to figure out where I went wrong. Dryer was working fine except for broken hearing element. I did take fuse and thermostat to work where guy checked them and they were working. Did I ground dryer while reassembling?

refrigerator isnt cooling in fresh food or bottom freezer also no fans ecept for compressor fan. Diagnosis showed freezer defrost sensor. after replacing sensor let run for 24 hours still no cool or fans. checked power board had 5 and 12 volts. replaced main control board. could hear Bottom freezer fan run after holding in light switch for 30 seconds. still no ff fan. Run diagnosis indicated main board was running fan. removed back cover and checked for voltage at fan connection. voltage was 0. also noticed coils were not frosting. assuming bad compressor or possible leak but would this cause the fan to shut down. will go out tomorrow and stick some gauges on it. Any help would be appreciated. Customer fridge has been down for four days

Hi i have a problem with the freezer coils freezing over with ice, the code flashes 3 but i just watched your video about the heater wrap around the freezer being replaced, the freezer drain is always frozen solid and wont drain without a lot of effort on my part to make sure it is clear, now the fridge side is getting a pool of water under the bottom drawer. looking forward to hearing from you, thanks for such a great site to come to for help!!! Ken
P.S. it is my understanding that the code means it is a sensor for the heater. ???

Do you sell parts?

was working ok but when the last load was put in dryer failed to heat

Freezer part is OK, but refrigerator part is not cooling.

As far as I can tell, there is a fan in the freezer that when the door is closed, it starts to spin and gets loud. When the freezer door is opened, it stops. There is also lots of ice starting to build up on the walls of the freezer.

i keep having the back panel on the fridge freeze up and eventually hitting the fan. you can see the ice coming out of the air holes in the back. it is also doing the same thing in the freezer department and that fan is making noise until i open the door. Which part do you recommend i order?

cannot find any info on the 1F code

I noticed this because I cleaned behind my washer and dryer and there was a small area that looked like water had accumulated there before. Not sure if that’s a problem or not? Cleaned it up and put a small towel there to see if I can catch anymore when it happens. Is something broken or leaking inside?

experiencing frequent Unbalanced Load error codes from her Samsung top load washer, model wa476dshawr/a1. The unit is firm on the floor and level. The error occurs regardless of the load size or type. Does anyone have any suggestions?

Every time i open the door and all throughout the day i here a noise that sounds like a pump trying to cut on. I have opened the door and it sounds like it is water or something trying to come through the lines where there is a container of some sort back behind the drawer and behind a cover. It looks like a water bottle. I don’t think this should be coming on all the time. Any help would be great.

Need Error codes & diagnostics for Samsung dryer

TEST MODE

How to diagnose.

I need error codes on this Samsung refrigerator model & troubleshooting guides ….thank you

I noticed ice in two of the top back panels. I unplug unit for 12 hours and then took off back panel to find a small amount of ice in top near fan. I have had no problems with cooling temps, freezer or standing water in drawers, I just noticed the ice. The drain heater was misaligned with a large amount of rust. A video said to use a copper #12 wire to keep drain plug clear. However, I am not sure if this was an issue as there was no ice showing in that location. So I am I am not sure how to proceed. Should I test heater and sensor? I am afraid to remove defrost heater since I have not had a cooling issue but I also do not want ice build up again.

Thoughts and thanks

Fresh side not getting below 50 degrees. freezer side working. technician has replaced thermostat Fuse, Heater, sensor. watching videos and internet searching makes me wonder if i have a evaporator fan motor issue.
still looking for manuals to see where located. any suggestion on what other parts could be the issue.

How do I get it back to normal? I can’t find our book for it and have been looking online but haven’t found the answer. I’m assuming it’s really simple but can’t figure it out.

We had this and it working fine at one location, and now not at it’s new location in a different house. Doesn’t seem like the compressor is even running at all. I opened up the back to take a look around and there is a harness that is loose, and stretched really tight from the compressor. I reattached it firmly in place and it came back on but I’m worried it will happen again with the wires being so tight and barely fitting where they are supposed to go.

replacing a thermister in a samsung wf393btpara /a2 Is this a simple repair or do I have to take off a bunch of stuff?
Is it a just take the back off and there it is?
I have a TE error.

Unit has been making noise for the past couple weeks. Freezer is working,no obvious icing issues.Fresh food section is not cooling.Is there a sure fire fix?

Not sure what the problem here is and would like this working since I have extended family here. Any thoughts or suggestions?

Is this something blocking the drain or the pump failing? My husband wants to try and work on it himself if possible.

Samsung dw 1E error code, model DW80F800UWS/AA, serial B009g9md604628d
This is supposed to be a high temp heating error. Had schematic for DMT800 series dishwasher with me. This wire diagram did not match the wire diagram on the main pcb cover on dw. Did not see thermistor listed on dw wire diagram on unit.
Heating element had 12 ohms, but no power going to it in quick wash cycle. Could not get it into diagnostic mode.
What should I be checking? I am guessing you need to pull the unit to get to components like LG brands?

looking for a service manual or assistance if anyone has heard of this problem its is a french door with ice maker up in refrig section and we replaced the Ice maker and the fresh food thermistor problem customer is stating the ice cubes are soft and melting what might i be missing .

Samsung ice maker model RF4287HARRS, SN: I02043CC1003. I first went out on the job and the IM did not cycle after I pushed the reset button down for about 15 seconds so I replaced the IM. On my second visit I found the IM that I installed had the fingers frozen onto the water inside the tray. I put another Im in this unit and made sure that it cycled by holding down the button for a few seconds and it did cycle (I dumped the water to make sure it wasn’t overfilled). But again no ice? Any ideas….

Having issue with Samsung refri. RS2530BSH the mullein heater between the s/s doors are very hot 155 degrees, my question is are the heater control by the main control board. Thanks

Diagnosed this dryer needing a new 4 wire power cord and terminal block. Problem is, I can’t find the terminal block by itself. Is this not available as a single part? Need some help on this one.