Brand: Thermador

Thermador

When set to bake, after about 20 seconds the unit codes out with f-34. tech sheet only says: replace air switch, then replace cooling fan, then replace control. all 3 have been replaced, in that order, and its still giving f34. the tech sheet doesn’t give any other information about the code. Anyone have any suggestions?

Looking for two Thermador hinges part # 00488417
Any help would be appreciated

Door handle coming apart and did not notice any screws or how to adjust it can I get a service manual Or something showing me how to repair the door handle and bottom hinge most importantly the doorhandle that’s the one I couldn’t figure out although I have fixed many

UPRIGHT BUILT IN FREEZER, THE CONTROL PANEL WENT BAD ON IT. THE FREEZER STILL HAS POWER.
NO DISPLAY AND NO COOLING

Hello Technicians,I have a Thermador Dishwashe that is not cleaning the dishes on the bottom rack or top rack . Dishes don’t look like they have washed at all. I thought it could be a low water issue, so I had the customer add hot water when the dishwasher stoped drawing water going into the beginning of the cycle, they said it didn’t make a difference. Please advise as to what else I might check. I have checked and cleaned spray arms, have Shop vacuumed out sump and drain. Thank you for you advise and help.

Any idea what error this could be ?

Hello Technicians, this is a follow up question, from my last question on this Thermador dishwasher.
I have checked all that was suggested from my last question on this product. Drain is clear and unobstructed. Wash arm spray nozzles are clear, detergent dispenser is working properly. Two things I have found ,when upper rack only is used and then you return to both racks the plunger that diverts water to the top rack sticks in the closed position and bottom spray arm does not work , I can take the spray arm off and take my finger and press the plunger down and the spray arm functions properly. I have also noticed the water in the tub is only 110 degrees. The flow through heaters do not come on and heat the water until about 30 minuets into the cycle, according to the service manual the dishwasher will pull 11 amps when The heaters are activated, the dishwasher pulls 1.5 amps for the first 25 to 30 minuets of both normal and heavy wash cycles. Can you advise me on how long into the cycle is normal for the heaters to begin operation and also the best way to stop the plunger from sticking. Any advise is appreciated.

Origonally the double oven had F64 Error code while either oven was on. Both fans working, we changed out the main control board. Now F64 error code after the top oven runs for a minute. The bottom oven works half the time, other half F64 pops up. There is no sell switch in this unit. What is causing this error code to pop up?

1. I would like to know if the drain pump that we need to replace for this unit fix the issue.
2. How to open this unit to access the drain pump area?
   Thank you.

Origonally the double oven had F64 Error code while either oven was on. Both fans working, we changed out the main control board. Now F64 error code after the top oven runs for a minute. The bottom oven works half the time, other half F64 pops up. There is no sell switch in this unit. We then replaced both cooling fans in both the upper and lower oven. Now after a while both ovens are not working and they have the original error code. What do we do next? Customer does not want to replace oven.

I have a Thermador built in refrigerator with a evaporator leak. The unit was built by Kitchen aid. I know the Kitchen Aid evaporator and heat exchanger are 1/2 to 1/3 the price of the Thermador parts. Does anyone know where I can find the Whirlpool part number for these parts or maybe get the equivilant model number.

Thanks
Mark Kelly
Kelly’s Appliance Center

THIS UNIT WAS ORIGINALLY OPENING ON IT’S OWN THEN IT WOULDNT DO THIS FEATURE AT ALL.

No coming out gas. The igniter is working good. What part we need to be replaced?

Hi Folks,

A Happy & Safe Fourth to all!

This unit is in very good condition and the problem element has not been used that much. Facing the unit it is located on the lower left, smallest element of the bunch. You turn the switch to the on position and the element switch lights up. Set the heat temperature and that lights up too. But no heat at all. Now I took the cooktop out and the element tests okay. Actually there is no wear at all on the element. Looked for disconnected wire(s) found none. Really don’t know where to go from here. Where is a good place to get a break down of Thermador products? Looking for some expertise from the Video Family.

Thank you,
Jan
Barney’s Appliance
Palm Bay, FL

Customer stated that the temperature isn’t right. Some times pre-heating isn’t working. This unit has an issue with temperature sensor?

looking for some help on this dishwasher that I went out on it couple of days ago customer had two other companies out . Unit was full filthy water . I put to drain and cleaned it out , also cleaned filter . Restarted unit it filled and didn’t wash sounded like it was draining some water out but nothing else. Found no tech sheet with unit. Ordered circulation pump when out and install put unit still doing same thing. I am not very familiar with this brand, any help would be appreciated. Thanks

I’m working on a Thermador range issue is with the top burners all igniters are working fine but the gas takes very long to open ( can’t hear it) , same issue with the griddle except that on this one you can see the spark going off before the gas comes on ,no flame , it looks like out of sync. I check the burner holes all are clean ,the issue is the gas is not heard until several clicks later. Any ideas or a manual for this one?

Hi,
Do you guys have any experience with the error code I mentioned above?

CUSTOMER SAYS THAT THEY HIT POWER BUTTON, IT STAYS ON FOR BRIEF MOMENT AND THEN SHUTS OFF. THEY HAVE TO PRESS THE POWER BUTTON AIN TO KEEP TURNING IT ON.
ERROR CODE F34 COMES ON AFTER POWER FADES. Tried to test power line going into unit to main board but not sure if low voltage should be present.

This unit has a new noise when she put larger cookware. It doesn’t makes noise all the cookwares she has.
What part do we need to replace in order to fix this unit? If it is normal, what exponation should we give out?
Are there any suggested cookware we have to use? Do we have to use Thermador suggested cookwares?
Thank you.

Need some extra eyes to take a look at this. Hopefully I can attach the information that is needed to try to determine how to properly wire this up.
Model of inline blower is VTI1010D

The hood and inline blower were installed in a house. New owner didn’t like it. Builder had it taken out and installed in another house. There is a connecting wire harness that runs between units. Naturally
that wiring harness could not be removed from original house. Electrician cut off the connecting end plugs to be able to match up wires. He wired it up and it don’t work. Builder saved the connecting ends, but that don’t help because
electrician took cut off wires out of plugs.

I have acquired information on wiring diagrams and schematics for hood and blower. I also find conflicting differences.
Here’s what I have come up with.

White wire from hood connects to blue wire at blower.
Brown wire from hood connects to brown wire at blower.
Red wire from hood connects to white wire at blower.
Blue wire from hood connects to red wire at blower.

Thanks in advance