0 votes
3k views

After this last wash, the “Control Locked” light came on my washer. We have unplugged, to try to reset but to no avail. what is the matter with my washer? Please help. Mine is a Whirlpool Duet Washer with the above model #. The dryer is fine but my washer….. There is no error code just the light

  • Desiree asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Whirlpool Refrigerator French door bottom freezer. The unit is all iced up where the Ice maker is? How to you take the Ice maker out? It has all snap parts with screws to come out.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

GOOD MORNING. THE CUSTOMER PURCHASED A NEW ICE MAKER. I DO HAVE 110 VOLTS AT THE MOLEX TO THE ICE MAKER. I INSTALLED THE NEW ICE MAKER AND JUMPED FROM L TO V AND T TO H WITH NO RESPONSE. I TESTED BETWEEN ALL TEST PORTS AND COULD NOT GET ANY VOLTAGE READING. I THEN INSTALLED THE OLD ICE MAKER AND JUMPED THE L TO V AND T TO H WITH NO RESPONSE. THEN I TESTED ACROSS THE L AND N AND GOT 110 VOLTS. PULLED THE MOLEX FROM THE ICE WATER INLET VALVE AND GOT 75 VOLTS WHEN JUMPED FROM L TO V. THESE TESTS WERE PERFORMED WITH THE FLAP AND DOOR SWITCH MADE. WHEN FREEZER DOOR IS OPEN LIGHT IS BLINK BLINK PAUSE. WHEN I CLOSED THE FLAP IT REMAINED BLINK BLINK PAUSE. NEVER BLOCKED OPTIC EYE WITH MY HAND. ANY HELP WOULD BE GREAT. THANKS, TODD FROM NY.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
6k views

get water but want make ice

  • aaron asked 10 years ago
  • last active 8 years ago
1 vote
3k views

Customer complains that his dishwasher Silverware rack dosnt dry at all, but the rest is dry???

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
442 views

To whom it may concern,
I have a whirlpool WRF757SDEM refrigerator that recently has a loud noise coming that appears to be coming from the top section. Last year I replaced the evaporator fan and thermostat as the unit has frozen up and stopped cooling. After that fan was replaced the unit was very quit and running normally.
Recently ( past 3 days) it has gotten very loud at times with a slight vibration. At times, the sound is very loud, but then it gets quieter; almost to normal levels.
The top unit is cold and maintains temperature, there isn’t any issue making ice and everything is cold and frozen in the freezer.
I am wondering if its an issue with the evaporator fan and if that needs to be replaced again.
Any and all assistance would be greatly appreciated.
Kindest regards,
Kris

  • toot033 asked 11 months ago
  • last active 11 months ago
0 votes
2k views

Evaporator and condenser fan motors running compressor running outer loop in front of door hot off and on open door light does not come on press button on control and light comes on but than goes out I suspect board is bad need video on how to replace the board and to know if I should check anything else compressor has a inverter board and when I open door switch what should my switch read when I check for continuity I do want to replace board without first being able to access the control and check board out I dont believe this has a main control board in the back correct me if am wrong

  • otrlopez67 asked 5 years ago
  • last active 5 years ago
0 votes
889 views

Hi,
I am troubleshooting a no LED light issue on this unit, All the LEDs work except the 5 on the roof of the refrigerator. The schematic shows that the 5 fridge roof LED’s are divided into 2 series circuits, 3 in one series and 2 in the other going back to the LED Driver board for the DC source. Both of these strings are not working, I have diagnosed that the LED Driver board is partially defective .

The problem is, it is not shown in any service literature, ANYWHERE. The visual shows it is located next to the control board along with the power supply, The only part shown in the exploded diagram is the Control board itself, Whirlpool W11161172. If you do a parts list search for LED Driver, it does not generate any hits. I am at a loss, I have check multiple sources including the Factory SM with no luck.

I need the part number for the LED Driver Board! Why is it not shown or listed anywhere? I wasted 2 hours looking!!!

Thanks 🙂
Tom
609 418 0278

  • thosk1051 asked 3 years ago
  • last active 3 years ago
0 votes
2k views

Condensation back wall in refrigerator and behind ice maker

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Freezer evaporator coils have no frost on them, however the fresh food is keeping temperature. I know these units are problematic with sealed systems. Which evaporator is the most common to change and what is the easiest way to tell which one needs changing, because I have seen this same situation before and it be the fresh food evaporator and I have also seen it been the freezer evaporator. Any advise would be greatly appreciated. All fans work.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Gas dryer igniter will glow for about 8-10 seconds the click and will not light. Could not find anywhere what the resistance should be on the igniter. Any suggestions on what else could cause this?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Have unplugged unit for long periods 2 hours or more trying to reset any faults , see no faults , plugged back in this last time and lock out light came on . cannot clear it with end of cycle button , and will not let any buttons work . Display blank.
First few times I could unplug for about an hour and re connect and it would come on and dry to end of cycle . But while drying you could not pause or cancel drying. opening door would stop it however.
Is it interface board or control board ?
Thanks ;
Steve

  • Steve Smallwood asked 10 years ago
  • last active 10 years ago
0 votes
2k views

I replaced the water inlet valve and the dual inlet valves due to the failed continuity readings. I waited 48 hrs and still no ice. I also felt no water in the tray, so I thought the icemaker water line was clogged-replaced that, and waited 48 hrs, and still no ice. Before I did all this I carried out the diagnostic tests you showed, and all systems were normal. Water pressure is normal in back and the water dispenser pressure looks normal. Icemaker dispenser sounds normal. Any suggestions? 

  • Gilbert asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Need service manual. Wonder if the freezer door SW controls the evaporator fan, light and something else?

Alex

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Hello
We have an ice maker that was not harvesting
1) We have good water pressure and inlet valve was replaced .
2) Good freezer temperatures at + 1 degree with two different temperature test devices, ice cream solid.
3) 115 volts to the ice maker.
4) Replaced water filter
5) There is one switch in series that is closed and we have power to the ice maker.
6) Replaced two different new ice makers. Whirlpool tech. line wants us to put in a third new ice maker ? I don’t think this is our solution.

We can harvest manually one time and drops nice normal thickness cubes. Then will not harvest again. There are no service bulletins on this # WPW10469286 ice maker. Has anyone else had issues with these ice makers or have any suggestions before we put in a third ice maker ?

Thanks in advance

1 vote
2k views

The refrigerator works perfect, except about every hour I get a 1 minute buzz for the evaporator fan motor then it stops and blows normal. Whirlpool Refrigerator

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Do you have more videos available for this make and model for the washer machine?
If yes can you help me locate them? thank looking forwarding hearing your response.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

I can’t get my washer to spin and I keep hearing a clicking sound. I’ve turned it on its side and took off the shield, the belt and motor turn freely by hand. After watching one of your videos, I’m thinking I need the shift actuator part # W10006355 but wanted to see what you think before I purchased it. The washer appears to have a small leak, the actuator looks a little rusty.

  • Lee asked 9 years ago
  • last active 9 years ago
0 votes
2k views

I have an odd problem, our duet washer is filling, with hot water only, when completely turned off and not in use. I came down to do laundry and found quite a substantial amount in the tub already. I drained it and did my load, and then checked the next day and same thing. I have a feeling this is also causing our hot water heater to run more than normal since the water is actually warm. Any help is appreciated.

  • Laura O. asked 9 years ago
  • last active 9 years ago
0 votes
13k views
  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

There is a fuse link in behind the control board on this model that is blown. It resembles a diode a little. I cant find this part on any drawing and was wondering if you could help me with the part number to this fuse?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

My Whirlpool washer is taking a long time to drain.

0 votes
3k views

Dryer shuts off during high heat cycle after about 10 minutes, will run on low heat just fine. The dryer will start back up immediately after it shuts itself off. I replaced the motor in this dryer a little over a year ago, to me this sounds like a motor issue, but a little confused as to why it runs on the low temp cycle. Run with the vent off as well and same results as before. Any ideas or suggestions?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

I am replacing the fresh food evaporator fan. I have watched your video on a similar model. This one is a 5 door and I’m not sure how to dismantle the draws and the center adapter between the two drawers.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

I need technical manual specifically to run diagnostics and enter forced cooling.

  • mbryan59 asked 6 years ago
  • last active 6 years ago
0 votes
2k views

We have came across many led issues on some of these refrigerators. Some lights won’t come on and when they are replaced they still won’t work even by replacing the boards as well. Please help

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
1k views
  • appliance7 asked 5 years ago
  • last active 5 years ago
0 votes
10k views

I ran the diagnostic on my Whirlpool washes I have blinking simultaneously light for FILL, RINSE and Done. What does this mean? Please help. I don’t want to try and open the top to get the tech sheet cause I need to know first what the problem is.

  • Elsa asked 10 years ago
  • last active 10 years ago
0 votes
2k views

do you think the 25 amp fuse would be the most likely of the problem?

  • robert asked 9 years ago
  • last active 9 years ago
0 votes
2k views
  • Guest asked 9 years ago
  • last active 9 years ago
Showing 1 - 30 of 2k results