0 votes
7k views

I have a customer that wants me to convert his LG dryer to LP. It is an LG model # DLG3171. I typed this number into your model # guide, with no results. I checked PartsPro website and that number came up. So I know that it is a good number. Do you have a video for this model # or something close to it showing how to take it apart? And 2, how long should a job like this take?
Thank you
Bob

0 votes
1k views

I am getting a 6C3 error code on my dishwasher. Also it will not do anything.

0 votes
2k views

Not heating, blinking complete cycle not staying solid

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Whenever unit is set to self clean winth 90 minutes it shuts down with an F9 error message according to customer have replaced control and checked for proper operation of door latch assembly all other functions work properly what could be the issue?

  • mra20168 asked 5 years ago
  • last active 5 years ago
0 votes
2k views

Evaporator and condenser fan motors running compressor running outer loop in front of door hot off and on open door light does not come on press button on control and light comes on but than goes out I suspect board is bad need video on how to replace the board and to know if I should check anything else compressor has a inverter board and when I open door switch what should my switch read when I check for continuity I do want to replace board without first being able to access the control and check board out I dont believe this has a main control board in the back correct me if am wrong

  • otrlopez67 asked 5 years ago
  • last active 5 years ago
0 votes
2k views

Gas dryer igniter will glow for about 8-10 seconds the click and will not light. Could not find anywhere what the resistance should be on the igniter. Any suggestions on what else could cause this?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views
  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views
LO

the unit will work sometimes .
put if I out it into spin I get the LO error and the unit will not run

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

Temps are warm in both freezer and fresh food dept. Compresser is running but freezer is hardly cold also no evap. fans are running in the frig. No error codes present. The brand is a Kenmore.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

I replaced the refrigerator main board and it doesn’t work Is my fridge completely dead?

  • Kristin Peterson asked 9 years ago
  • last active 9 years ago
0 votes
2k views

ok. so I goo to repair videos.type in the above model #. click on tech sheet and it won’t give it to me. what am I doing wrong?

  • mrfixit asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Condenser fan cycling on and off every 10 seconds. everything else is working fine.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

So the dryer was making a rattling sound when it starts and ends.
I thought it was the belt or ideal arm so I changed them .
No luck the noise is Evan worse now and the drum has no force to it.
Meaning if I put in a wet load it will not turn.
2. After I put the dryer back I have a strong burning smell when we start the washer.
It filled with water but will not advance to anything else.
I hear the timer clicking but that’s all I Get.
It is a 25 year old machine.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Just installed a brand new tankless hot water heater, the pilot light will turn on for one second make a clicking sound and turn off again. The main burners will not light. What would cause a new hot water tank to not light?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
8k views

Our dishwasher quit working and is flashing an ER code. How do we diagnose what it needs?

  • Chris Higginbotham asked 9 years ago
  • last active 9 years ago
0 votes
3k views

My dishwasher will not start. The lights light up when I choose different functions but it won’t actually start when I press Start. I tried the reset by pushing the High Temp Scrub and Energy Save Dry buttons alternating five times each and the unit will go through the reset. It also drains when I press cancel after resetting. I am not sure how to proceed.

  • Ryen Mullen asked 9 years ago
  • last active 9 years ago
0 votes
24k views

Frigidaire refrigerator fphg2399pf1 is dead. No lights . . . not working. Tested outlet. Have electrical diagram. Mother board has power. Ordered new motherboard. Did not fix.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
6k views

get water but want make ice

  • aaron asked 10 years ago
  • last active 8 years ago
0 votes
11k views

I have examined the heating element of this Samsung dryer; but it did not appear broken. The coils were a bit black in some places but nothing broken. The inside of the dryer was filthy with lint … on the motor, in the heating element, and clogged in the lint exhaust hose. The tub spins and it has power. Is this low heat condition and indication that the heating element is going out or is there a problem with a thermostat not working correctly? What would cause a low heat condition in the dryer?

Thanks-

Fred / Lubbock, TX.

  • Fred asked 9 years ago
  • last active 9 years ago
0 votes
3k views

I need some advice from our subzero experts.
Complaint: Not Making Ice.
We found the unit with the icemaker arm bent around from the bucket being pushed back on the arm.
We replaced the icemaker and as the water level was low and it is in a rental home we removed the filter and installed a factory by pass plug.
I started the unit in Max Ice. The icemaker cycled around twice and filled to the correct water level. We thought all was good and stopped to double check it the next day, No Ice.
I checked everything over again, drawer switch etc. ok.
After posting on psanet we replaced the complete water valve w/flow sensor. I opened the valve sensor and found it had droppings in it. We thought we were ok.
I started the icemaker again on Max ice and stopped to check it again 2 days later. Still No Ice.
The wiring seems good . Power to the flow sensor comes from the Low Voltage Board and Power to the icemaker comes from the high voltage board.
Factory tech line doesn’t think it is a board.
Any advice would really be appreciated.
Thanks in advance.

0 votes
2k views

Condensation back wall in refrigerator and behind ice maker

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

how do you tell if your control board is bad

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
7k views

Washer gives f35 and sud error. Trap is clean, technician came and replaced the switch. Washer worked for about a month, getting f35 and SUD error again. Basket is clean. Please help.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Freezer evaporator coils have no frost on them, however the fresh food is keeping temperature. I know these units are problematic with sealed systems. Which evaporator is the most common to change and what is the easiest way to tell which one needs changing, because I have seen this same situation before and it be the fresh food evaporator and I have also seen it been the freezer evaporator. Any advise would be greatly appreciated. All fans work.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
442 views

To whom it may concern,
I have a whirlpool WRF757SDEM refrigerator that recently has a loud noise coming that appears to be coming from the top section. Last year I replaced the evaporator fan and thermostat as the unit has frozen up and stopped cooling. After that fan was replaced the unit was very quit and running normally.
Recently ( past 3 days) it has gotten very loud at times with a slight vibration. At times, the sound is very loud, but then it gets quieter; almost to normal levels.
The top unit is cold and maintains temperature, there isn’t any issue making ice and everything is cold and frozen in the freezer.
I am wondering if its an issue with the evaporator fan and if that needs to be replaced again.
Any and all assistance would be greatly appreciated.
Kindest regards,
Kris

  • toot033 asked 11 months ago
  • last active 11 months ago
0 votes
4k views

I ordered the part 819160 .It is oem.The installation instructions list four procedures .Does this unit have start and run capacitors? It has a battery sized one and a part that is wired to it with a blue wire and red wire.The part has a copper winding on it.This part plugs into the compressor,is it the run cap?The big cap has two red and one blue wires connected to it.Can send pictures.How do I wire this?

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
3k views

Customer complains that his dishwasher Silverware rack dosnt dry at all, but the rest is dry???

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Hello, I love your new website.
My customer has a GE French Door fridge with the freezer on the bottom. I think the board that controls the fans is bad. I am the forth technician to service this fridge. She has had nothing but problems with it since she bought it. A year after, GE replaced the compressor. After that 3 boards were replaced. And more! Now this?..

Showing 31 - 60 of 9k results