Repair Help

tried new pump with old board and old board with new pump and new pump with new board same issues

I performed the callibration test as listed in the video and I got two error codes ,F-7, E-5.
could you please tell me what they mean?

Keeps getting F28 Error Code. Sometimes it finishes a cycle and sometimes not and comes up with F28.

Please help on error code F8E0

Oven light turns on by itself , how can I prevent this from happening?

What does this part do? Does it recycle the water. I would like to know. Will it stop the dishwasher from turning the motor on if it doesn’t work?

Both the fridge and the freezer are not operating at their proper temperature. They are both cool, but the fridge is not cold, and the freezer is not freezing.

why does Kenmore upright freezer top shelf have a big big frost built up none of the other shelfs do this this is a very simple unit manual defrost no interior fan.

Giving error code 5a6 or sab on display nothing work

Frig and freezer run hot compressor runs condenser fan runs don’t know about evaporator fan when door is open can hear it when door is closed can’t hear it. Is there a way to check to see if its running? Doors don’t have switches (push in ) its a magnet at bottom of freezer door.

This code says cooling fan speed too low or won’t come on. Do you have a video on this one and a service manual and any tips?

My question has nothing to do with the specific model number of above. A coworker and I changed out a bad compressor. It ran for 2 days, then stopped. We were discussing our problem with other techs. One of the other tech asked us how we filled the new compressor with freon. We told him that we filled it with liquid on the low side line like we always do.
He said that we improperly filled the compressor and thus, broke it. He told us that the only way to properly fill a compressor is liquid on the high side and vapor on the low side. Now, we have made over 25 compressor change outs, and never had a problem.

What is the “only” or is there an “only way to fill a compressor?

This samsung dryer is running for 2 min. then drops to 1 min. left and ends cycle. I noticed the back legs had dropped off the top of the washer. I lifted it back up and cleaned sensor bars, but cycle still shutting off in 3 min. Any ideas?

I have a whirlpool washer that the motor isn’t running. I am getting error code F7 E9 which is not on the tech sheet. i seem to have a open winding. I am assuming I just need to change the stator. Has anyone else had this issue?

Looked online and technical manual both say check wiring from door latch to CCU or needs new latch. I tried a new door latch still error won’t even lock or start. Checked CCU board for burns looks good, checked wires for continuity good..
Could it just be needing a new CCU AND will I have to program it to take $2 dollars again for a wash with the new board or is that a separate computer inside the coin slot thing? Please keep the answer simple brain dead after this one.

During self test mode I got these three error codes relating to fill and drain cycles. E22, E23, E31
I replaced the water valve and flushed out all hoses and filter from drain section. Still had same problem.
Wash cycle starts with no issues. Water enters and fills tub, soap enters and wash cycle progresses.
The whole wash is supposed to last 59 minutes. The customer stated that his cycle stopped twice. once at 44 minutes and a 2nd time at 17 minutes during spin cycle. When I tested it, it stopped with me once only at 21 minutes going into spin cycle.
I was listening to all sounds from the washer during the entire 59 minutes. At 21 minute mark, the tub stopped turning, the drain pump sounded as if it was working but the start button on top panel was lit up like a xmas tree. I guess it was waiting for me to press the start button in order to advance the cycle. When I pressed the start button a second time, the tub continued to spin and the cycle advanced. Does this sound like a control board issue, a timer issue or drain pump or other ?
For this model, I think the timer is part of the control board.

Getting error code f8e5 exhaust air temp sensor can’t seem to find a part number for that

Whirlpool Cabrio Customer complaint it doesn’t complete spin cycle, water is pumped out but clothes are still wet. They start spin cycle to finish load.
Error codes:
F7E7 – Motor unable to reach target rpm
F0E2 – Over suds
F7E1 – Basket speed sensor fault
Unit agitates and spins in diagnostics. There is no clothes caught between tubs. There were no flashing lights when performing the tachometer verification mode. Wires and connections were good.
Not sure if this is a shifter problem or main pcb problem?

Seems like the main oven door is not contacting with the latch/light switch.

This is the first time we are seeing this refrigerator. It has a feature known as “AutoFill”. You place a cup or container on the water/ice dispenser platform and the fridge automatically fills the container to the appropriate level. This particular fridge keeps displaying “No container” when you place a cup and hit autofill. I tried researching this and found that it is sometimes the result of a non-uniform container. Our technicians tried several container types that were uniform and still received the same error message. All other functions of the refrigerator are working fine.

It worked for one day and now giving code again. Any ideas?

I am working on a 4 door kitchenaid refrigerator that has icemaker in the celling in refrigerator side how do you get it out , dose anybody have a service manual to share whit me MOD#KFIS29PBMS02 and SER#K33307442 help is very appreciated