The wash program selector is stuck on “Rinse” and will not move.
- Ed asked 9 years ago
- last active 9 years ago
I was advised to switch the button control units as the top drawer selector will not move from rinse.
How do I access those controls? Is there a walk through? Diagram?
Do I need a serviceman yet??
- Ed asked 9 years ago
- last active 9 years ago
HOW DO I TROUBLESHOOT THIS? I SUSPECT BAD WATER VALVE. NO WATER IN TUB AND COMING UP WITH U6 ERROR CODE. THANKS.
- mdhomeservices asked 6 years ago
- last active 6 years ago
Parker &Fisher, not spinning motor getting hot? Is there a way to know transmission is bad? How do you put this machine in diagnostic mode?
- Guest asked 8 years ago
- last active 8 years ago
Hey Guys.
I am attempting to replace the baring on my Fisher & Paykel Drying.
I managed to remove the baring. However, the washer (SHIELD DUCT INLET) on the backside, can only be reached by removing the entire
outer casing.
The shell appears to be attached at the bottom by the feet.
I can’t figure out the mechanics of how the feet are attached.
Hope you can help.
Carl (504) 460-7242
- Guest asked 6 years ago
- last active 6 years ago
Washer isn’t going into spin cycle?
- Guest asked 8 years ago
- last active 8 years ago
Not very knowledgeable on these yet and am wondering if it’s a bearing like many other brands? Has a slight rubbing noise as well, am thinking it may be more than one thing but not sure. Any help would be great.
- David Sutton asked 9 years ago
- last active 9 years ago
Hello,
Our Fisher & Paykel DEGX2US dryer takes forever and does not generate much heat.
After cleaning the dryer inside and out and removing a lot of lint, I followed your fantastic video at http://www.youtube.com/watch?v=OpZXoD16uvs. I was hoping that the resettable switch had tripped, but it appears that the rear element is the cause as it failed the simple continuity test. Is there a way to fix it (fuse? detached wire?) or should I order a new element from you guys?
Thank you for the great site, videos, and service!
Dotan
- Dotan asked 10 years ago
- last active 10 years ago
DCS WOT-230 only heating to 265 degrees on top oven bottom ok, remove oven check elements, stats, all wiring connections, top sensor and lower sensor was a little different in ohms, so swapped them now top oven heats to 320 only when set for 350, lower oven still works fine, I thinking that the MCB is bad, anyone have any experience with this issue?
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
Unit is not making ice. Unit has flex tray ice maker, could not locate any harvest button for the ice maker. The display was not working on front of door, fixed damaged wiring to get display running (On off switch for ice maker on display, display was not functioning for years), After this worked, was looking for fault codes on main display based on tech manual, none showed. Put unit in to test mode, would not show any error codes on front display. Based on tech manual, the control has blinking lights on ice maker module part of PCB, there was no blinking lights that indicated any problems with ice maker. Followed tech manual to OHM check motor, switch & thermistor based on temp guide from UI, all checks out fine. Ohm’d out the water valve, this checks out fine, water pressure through front is great. Is there any way to cycle this ice maker? Or a way to activated water valve perhaps by switching the inlet wires and pressing for water? Thanks in advance
- Curtis Appliance Repair asked 8 years ago
- last active 8 years ago
The clothes are still coming out of the dryer wet.
- Fred Abernethy asked 7 years ago
- last active 7 years ago
Physically damaged, Affecting the operation of the door.
- Patrick's Appliance Service asked 6 years ago
- last active 6 years ago
Clothes come out wet, light comes on but will not run.
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
dryer is drying But it seem like the heating Element stays on. I have taken it apart and seen the one of the elements is burned out. So now that i am waiting for the part is there anything else that would cause that element to stay on..
- wenzel asked 9 years ago
- last active 9 years ago
I’m trying to find the part information on a middle (center) burner electrode kit. I don’t even know if I can replace it without some help getting to it. But if you have some part information that would be helpful.
- James Buchanan asked 9 years ago
- last active 9 years ago
I just applied the reset button on the heater housing thermostat and ran an operation test that was successful. Should I price out that thermostat for replacement or will that work?
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
How do you remove the basket from the drive unit?
- Guest asked 8 years ago
- last active 8 years ago
The water will not drain out of my Fisher & Paykel washer.
- Harley Clark asked 7 years ago
- last active 7 years ago
Cannot change settings, Unit will not cool, Unit has no power, Unit will not stop running.
- T&G Appliance Repair asked 6 years ago
- last active 6 years ago
Steam cycle will not work, garments are not refreshed.
- Patrick's Appliance Service asked 6 years ago
- last active 6 years ago
My research leads me to believe that it is the actuator. agree? and if so, I’m not finding a video.
- Bill asked 9 years ago
- last active 9 years ago
Some kind of error lights are coming up the customer said but I’d like to try and take a part with me if possible. Any thoughts?
- David Sutton asked 9 years ago
- last active 9 years ago
My Fisher&Paykel makes the room hot while running & dryer seems to overheat .
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
My unit has FC error code and will not start ? Can you help
- Harley Clark asked 8 years ago
- last active 8 years ago
I have an issue with a Refrigerator, it’s a Fisher & Paykel and this is the problem I am seeing: Compressor will not start
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago