0 votes
4k views

Bake and Broil shut down when temperature
reaches approximately 250F. How do I correct this ?

0 votes
3k views

Surface elements will not work and the light ring around the knobs will not illuminate.

0 votes
3k views

Ice or Frost Formation Around Ice Box Door Opening

0 votes
4k views

diagram 3 part 316 shows a hub belonging to the washer, after removing the tub from cabinet, and removing all securing hardware from the inntertub to the outertub, the hub will not release from the bottom of the outertub. Is there a special procedure for removal, or is it simply stuck in place? Need to know in order to find and replace tub bearing, along with tub seal.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

The hose that comes out of the refrigerator goes behind the compressor to the front of the refrigerator. Can this hose be replace on a GE Profile refrigerator?

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
3k views

The high limit right thermostat on this unit which would cut power to the motor located on the right side of the heating element , when this goes out what usually is suspected or root cause of that?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

refrigerator icemaker not making ice, unique design, looking for a service manual and any service updates pertaining to the icemaker for this model.

Thanks

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
4k views

freezer staying at 26 deg. fresh food at 34 deg. replaced main control board after finding only 3 volts d.c. on the inverter input from main control board.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

Besides a bad belt, what other components could cause the belt not to turn. The washer stopped on its own, did not trip any breakers, it would advance to the next cycle manually but the belt was slipping and tub was full of water. They cut it off after this. I have not been there to check it yet, I was told this on the phone.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

GE Monogram 36 or 46, both the hood fan and the lights not working

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

My Whirlpool refrigerator is not getting any power at all.

0 votes
3k views

The lights in my refrigerator are not working.

0 votes
3k views

My refrigerator is not sitting level on the floor.

0 votes
3k views

My cooktop keeps beeping why is this?

0 votes
2k views

My cooktop takes a long time to heat up.

0 votes
2k views

The front right burner is out on my cook top.

0 votes
3k views

The knob on my cook top is broken.

0 votes
2k views

I am concerned because my range smells like gas.

0 votes
3k views

The control panel is not working at all on my cook top.

0 votes
3k views

My cook top smells like its on fire.

0 votes
3k views

The back two elements on my GE cooktop will not light.

0 votes
2k views

The knob on my cook top is broken.

0 votes
3k views

Original issue was it was not defrosting at all now after I replaced the main board and Defrost bimetal thermostat with a thermostat I had that was a WR50X55 The customer says the temperature fluctuates between 35 and 45° F once or twice a day so I’m guessing it does not defrost frequently enough. Could it be that I put in a random GE defrost bimetal thermostat that I had on me? Let me know what you guys think I want to stop by there this afternoon and fix it and if I could have a basic explanation of bimetal defrost thermostat’s maybe there something I don’t now because most fridges if it’s not defrosting you need to replace the Defrost control but certain fridges just replacing the thermostat will suffice.
HEATER TESTED OK. I replaced the thermostat just in case, I did not suspect it of failure.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Hello Technicians Thank you in advance for your help.
This General Electric side by side has a frozen up evaporator. Heater and defrost thermostat are good thermistor seems good. Suspecting adaptive defrost control board. This model is not electronic touch control, it has the mechanical dials to set fresh food and freezer settings, my question is is there a way to put this fridge in a forced defrost ?. Any advise would be much appreciated. Also wondering if you have encountered any bad solder joints on these boards?
Thank you once again for your help. Any advise is appreciated.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

The unit will not agitate or spin. The only error code it gave was 0d3. I can not find any information. Thank you in advance.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

My GE oven will not keep the proper temperature.

0 votes
3k views

My GE oven just starts then stops.

0 votes
2k views

My GE oven is giving off a burning smell.

0 votes
2k views

The lights in my oven are not working.

0 votes
3k views

The fan in my oven makes an odd noise.

Showing 541 - 570 of 2k results