Brand: Fisher & Paykel

My dryer will not spin do you have any suggestions to rectify this issue?

Hello I have a question on a Fisher & Paykel Refrigerator. I’m noticing these issues: Will not dispense water

WE ARE TRYING TO INSTALL A 24840P SPARK MODUAL ON THIS DCS RANGE, MY TECH CANT SEEM TO FIGURE OUT HOW TO TAKE IT APART. WE ARE LOOKING FOR A SERVICE MANUAL OR REPAIR MANUAL IF IT IS AVAILABLE.

THANKS!

sticker is pealing off, settings are unreadable, console is loose.

Checked internals-Pretty clean
Checked heater-seemed fine
Checked both thermostats on the heater-seemed to be fine but couldnt test when they open
Everything else in the dryer seemed to be ok, the dryer element was cycling off and on throughout the cycle and i know one thermostat cut off is 115 Celsius which when it ran i did notice the dryer was about 200f inside which is on par with that thermostat but there is another thermostat with a lower rating which didnt seem to affect it. Let me know what yall think. Dont really need any diagrams just someone more experienced then me opinion.

Just wanted to post a reminder to all those out there that may read this: I’ve had more burning smell & lint build ups this year than ever before. Just came across another today. Many have had a flame rollout has already caused some burning lint and there’s limited air flow causing long dry times. Please be sure to clean out these dryers if you’re in there working on them already, and if you can’t get the vent completely cleared, have a professional come do it, or strongly suggest it to the customer. This becomes such a serious fire hazard when left alone and unnoticed.

What would cause this?

Having an issue with a Refrigerator

My refrigerator is not making ice.

Hey Guys.
I am attempting to replace the baring on my Fisher & Paykel Drying.
I managed to remove the baring. However, the washer (SHIELD DUCT INLET) on the backside, can only be reached by removing the entire
outer casing.
The shell appears to be attached at the bottom by the feet.
I can’t figure out the mechanics of how the feet are attached.
Hope you can help.

Carl (504) 460-7242

Clothes are getting torn, laundry ends up in a balled up or knotted the end of cycle.

Not very knowledgeable on these yet and am wondering if it’s a bearing like many other brands? Has a slight rubbing noise as well, am thinking it may be more than one thing but not sure. Any help would be great.

Checked the inlet valves, hoses, made sure I had water to the unit – it all looks good. Am now wondering if there’s an issue with the drain pump that is causing the unit not to start a cycle at all because the customer says it hasn’t been going into drain by itself, she was manually making it. What’s the part information for the pump if I do end up needing that?

Washer code 159

The drum will not move on my Fisher & Paykel dryer.

Does anyone know how to read the new producy codes on Fisher & Paykel appliances

Unit will not run, will not start.

I’ve got an error code E08,03 – short circuit coil, wiring to coil or controller, replace controller

The water seems to be entering the tub okay when I put it into diagnostics, however when I tried to put it into a short cycle diagnostics mode, the dishwasher wouldn’t enter into this diagnostics mode. I’m suspecting a bad control board.

DCS WOT-230 only heating to 265 degrees on top oven bottom ok, remove oven check elements, stats, all wiring connections, top sensor and lower sensor was a little different in ohms, so swapped them now top oven heats to 320 only when set for 350, lower oven still works fine, I thinking that the MCB is bad, anyone have any experience with this issue?

              Unit is not making ice. Unit has flex tray ice maker, could not locate any harvest button for the ice maker. The display was not working on front of door, fixed damaged wiring to get display running (On off switch for ice maker on display, display was not functioning for years),    After this worked, was looking for fault codes on main display based on tech manual, none showed. Put unit in to test mode, would not show any error codes on front display. Based on tech manual, the control has blinking lights on ice maker module part of PCB, there was no blinking lights that indicated any problems with ice maker. Followed tech manual to OHM check motor, switch & thermistor based on temp guide from UI, all checks out fine. Ohm’d out the water valve, this checks out fine, water pressure through front is great. Is there any way to cycle this ice maker? Or a way to activated water valve perhaps by switching the inlet wires and pressing for water?  Thanks in advance 

My dryer is not drying my clothes all the way

Can you tell me what could be causing this issue on a Fisher & Paykel Dryer? It is having these problems: Cannot select cycles

Service wrench symbol illuminated, Dispenser light not turning on, display continually blinks.

I’m trying to find the part information on a middle (center) burner electrode kit. I don’t even know if I can replace it without some help getting to it. But if you have some part information that would be helpful.

I just applied the reset button on the heater housing thermostat and ran an operation test that was successful. Should I price out that thermostat for replacement or will that work?