Brand: LG

Found the element bowed from repeated overheating and the hi limit open. Looks like I’ll need that entire element assembly. What’s the pricing and availability of it?

Diagnosed this as needing a new control board. Anybody there have time to do a quick lookup for me? Appreciate it.

I found this unit to need the main board and the display after diagnostics. Can someone shoot me over those part numbers and pricing? Thank you, appreciate it.

replacing customer supplied door gasket .we confirmed correct part # msd47263101.seems to be to big to fit any tricks to this? or do you have video on it?

Checked this unit and removed debris/cleaned spray arms and checked the inlet valve, looks like it’s the culprit here. Problem is, I don’t have the ability to do a lookup today. Can someone there find that part info for me? Appreciate you guys.

Washer hearing a roaring sound in high speed spin, possible bearings? Library does not have this particular model it does however have a WM2077CW is that a close enough match to be of any help?

This refrigerator was operating normally except for a noisy condenser fan. When I moved the refrigerator to replace the motor the compressor started clunking which continued for several seconds before it quieted down. Is this a catastrophic problem? The refrigerator continues to operate normally.

LG dryer starts and heats when cold but after unit heats up it shuts off like the board drops the load lights on but no start.
won’t restart until cools slightly but then drops off again and repeats. I am thinking bad board anything else about LG dryers,
I don’t know about. No Fault codes?

I found the water leaking from the hot water valve and am changing that out, but the suds/foam…I wasn’t sure how to take care of that.

WM2455HW
A few years old. FE code. Fill error. Checked all fill solenoids/ checked good, put in new pressure switch and machine behaved better. five minutes after I leave I get a text that the FE is back(happened in rinse cycle).
Anyone know these better than I do?

A few years old. FE code. Fill error. Checked all fill solenoids they were
good, put in new pressure switch and machine behaved better. I
watched it for 15 minutes and left. Five minutes
after I leave I get a text that the FE is back(happened in rinse cycle).
Anyone know these better than I do?
.

The washer won’t lock and actually start, just has a buzzing/ticking noise. I think it’s the door lock but can’t find the part information or a repair video for it. Any help?

I’m pretty sure this is a tub boot, but I’m having a heck of a time finding the info for it. Would really appreciate some help if you have a minute.

This washer isn’t spinning and it seems like the clutch is the problem. It looks like from the diagram that it’s an entire housing assembly, is that right?

I feel as though I’ve checked everything on here. It’s not the heat because it’s getting plenty hot, fuse & thermostat tested fine. Control was still good, venting looked clear from inside and I checked the outdoor, even though it did seem to have some diminished air pressure it may just be due to such a long run from the laundry room. Any ideas?

Summary above is per the customer, I’m heading out there and want to take a control with me. Anybody there have the part information for me? Am pretty sure this is the issue.

I found this unit to need starting components, but couldn’t find them separate from the compressor. How can I get just what I need?

Pretty sure this is a rear bearing, but the customer is opting to replace the unit because it’s too costly. Do you know of anyway to get it cheaper?

This needs a touchpad but I can’t find the part lookup information for it. Thanks.

I found this unit in need of a new pcb main and user interface. Problem is, I can’t find the parts available anywhere, thought maybe you’d have better luck.

I checked the control it seems ok, so I’m assuming it’s the touchpad. Do you guys have some part information there you could pass along for this? Thanks.

I got this torn apart and it seems like the rotor assembly is the main issue here. I don’t do many of them, but was hoping someone there had time to shoot me the necessary information over while I’m here. Didn’t find a repair video but think I can handle it without.

I think this needs a new pump, found the part number as 4681EA2001T. Can someone just confirm that for me?

One of our guys has this unit that isn’t starting. He took it apart to diagnose and said he found the noise filter bad. I don’t think I’ve ever replaced one and then couldn’t find it when I did the lookup for him. Anybody have a few minutes to help me on this?

This unit is stopping in the middle of it’s wash cycle with an “ee” error code. Any ideas on what it is before I get there to diagnose?

This unit is not reaching pre heat or even maintaining any temperatures. Checked all the heating components and they are fine. Got to main relay board and found it bad, cannot find it in stock through my vendors, do you guys have it?

Condenser fan cycling on and off every 10 seconds. everything else is working fine.

CAN YOU PROVIDE STEP BY STEP ,LG REFRIGERATOR REMOVE THE FROUNT PANEL SO I CAN CHANGE THE DISPENSER SPRING,DOOR CHUTE,