Brand: KitchenAid

I know you sent this to me but I cannot find it in my IPad could you please resend It

Error F6 E1 , RUNAWAY TEMP is displayed.

I also received an answer 1 hour ago which suggest me to go to page 62 of Job aid.
But i cannot find Job aid page of Tab!
Can you help me
Many thank!!!!

Gas dryer keeps shutting off. I can sometimes get it to complete a full dry after a few start/stop cycles.

When I press ‘start’ either on auto or timed cycles, the dryer will start for about a minute, then stop. Or when the start is pressed, the relay clicks and the drum (I have the top removed) moves about a 1/4 inch. I then press off/then start buttons until the dryer starts (each unsuccessful try the relay clicks and the drum slightly moves). It may take ten off/start button cycles to get it to start again. After which, it may stop after 1-5 minutes or go the whole dry cycle. Sometimes if the start/off button can’t get it to start, then pressing the control button to turn off the lights and then control button to turn on lights and then start after that sometimes works.

The refrigerator side is not keeping cool enough. The door just falls open and appears to have no suction. Normally on this unit the interior wall is warm but it is not warm on this one.

The door on my dishwasher just falls open.

My KitchenAid refrigerator is not turning on.

No power on water valve

I have this double wall oven. The MW display says door. I have run into this before but those MW’s have two cartridge fuses, and one would blow. This MW only has one fuse and it is good. The door switches checked good, but I replaced them anyway, still didn’t work. Anyone have an answer or suggestion ?

is half of the dual broil element suppose to come on in bake mode?

My Kitchenaid refrigerator is not dispensing ice.

No ice or water at the door not getting power at water valve and can’t change water level at display kitchenaid told me to order display and control board kit and I needed to do both so installed new parts then the frig compressor would not turn on put the old board back in at the back and it turned on but still no water or ice also both the new ones did not not fix the the no water and ice

My Kitchenaid stove has streaks in between the glass

I had read, in the past, that the time the system takes to equalize can indicate the problem in the sealed system. Is this the case, and if so can you elaborate?

hi. damper stuck closed. i opened vanes with small screwdriver. put unit into diagnostics. on step 5 damper received 120 v ac. closed the damper vanes but would not open them with a constant 120v. problem is when unit is calling for cold the board is not sending 120 to damper. ff thermister was placed in ice water. reading was normal. i know the damper is bad but is the board bad also. freezer temps are good. compressor runs constantly. yhanks.

Hello again,

I have an ongoing issue with a KitchenAid building unit, first I found a refrigerant leak coming from the evaporator (I noticed that a lot of yellow oil came out of the same spot on the Evaporator. I replaced the evaporator, filter drier and flush the system with nitrogen. When I flushed the system a lot of yellow oil came out. I vacuumed the system for 20-30 min and recharged the system with 7.25 oz. the pressure did not go down lower then 20psi on the compressor side.
but I noticed that the freezer was stabilized. two days after the customer called me back and said that freezer is still cold but not enough.

What else in your opinion can be done? replacing the capillary tube might be a very big job on this unit so I’m trying to avoid that as much as I can.

I would really appreciate any help you can provide in this case

Error F3 E0, Error F6 E0, Unit will not self clean.

The dishwasher has power. The Hi-scrub light is on. No switches will activate any function. Nothing comes on when the door is closed.

First call was not cooling. Diagnosis showed fans not running and not getting 120 Volts to inverter. Replaced main board (W10801767). Getting power to inverter but fans still not running and compressor not starting.

Tested board for power to (DC volts) to Compressor (5-6 volts DC) and not getting a reading. Diagnostic mode says fans are running? Compressor windings test good between 6-7 ohms as spec. In diagnostic mode thermistor show a 00. Have I overlooked something? Think a faulty board?

I can’t figure out how to access the refrigerator evaporator, need a service manual.

My Kitchen aid dishwasher is not cleaning properly.

My Kitchen aid dishwasher is not dispensing any water.