0 votes
104 views

How to get water automatically in the Ice Maker?
Is the user interface display related to this problem?
Which specific part is responsible to send the signal to the core control board so the ice maker can be filled up?
Does the ice maker sends the signal to the core control board to be filled with water?
How does it work?

  • rafa3092 asked 1 month ago
  • last active 1 month ago
0 votes
74 views

Yesterday my refrigerator completely quit working. The internal display was off, as well as the external. Only the internal lights worked. I reset the circuit breaker to see if the refrigerator would reset. Nothing. This morning the refrigerator is working – all display work and it is cooling and making ice. Why did it do this and how do I trouble shoot or repair?

  • Lyleric asked 2 months ago
  • last active 2 months ago
0 votes
108 views

I need a tech sheet/diagram for this. Unit has no display, only thing working is top burners.

  • user asked 2 months ago
  • last active 2 months ago
0 votes
152 views

We replaced a compressor in the refrigerator that wasn’t cooling at all. The freezer now is getting to -10 but the refrigerator wont get below 45. We replaced the evap fan motor, control board, and both dampers. checked all vents to look for obstructions found nothing. There seems to be no airflow into the refer from the freezer once the freezer door is closed but once it opens then it seems like it gets a lot more airflow. Is there any common airflow issue or any solution we haven’t addressed yet? Please advise

0 votes
204 views

The refrigerator is sweating alot of water on the ice bin and the entire assembly there is cooling but it has alot of water why is doing that what part it needs to be replaced there

  • Cocoazul20 asked 5 months ago
  • last active 5 months ago
1 vote
270 views

Replaced new compressor heat exchanger tubing and new evaporator and new filter.Charged 7.00oz and still not cooling low side is -20 psi and high side is 77 psi.compressor pull1.2 amp

  • matteo asked 8 months ago
  • last active 8 months ago
0 votes
317 views

refrigerator makes a noise in the freezer and it has a lot of ice in the back

  • Victor12 asked 1 year ago
  • last active 1 year ago
0 votes
466 views
0 votes
540 views

5 DOOR REFRIGERATOR HERE AND IS GIVING PO CODE. THE MAIN BOARD AND THE POWER CONTROL BOARD BOTH HAVE BEEN CHANGED. THE COMPRESSOR CYCLES OF AND ON ABOUT EVERY 30 SECONDS TO A MINUTE. THERE IS FROST BUILD UP IN THE MIDDLE SECTION AND SOME IN THE FREEZER SECTION. ALL WIRES IN THE LEFT DOOR HAVE BEEN SPLICED. SOMEONE TOOK THE TECH SHEET, SO I CANNOT GET INTO DIAGNOSTIC MODE. ANY HELP ON THIS ONE WOULD BE WONDERFUL.

0 votes
411 views

The machine is cleaned regularly and still looks like new although over 10 years old but recently it has been making a churning noise from the pump and noticed the water reservoir not filling all the way or not filling. 8 have turn off and on after resting it for 30 minutes and it will make another sheet but 5he same thing. The water flow each time I start the machine is strong as always but can’t figure out the problem. I’m pretty handy and have replaced parts over the years but this one has me stumped and nothing is on the internet with these systoms.

  • recklem asked 1 year ago
  • last active 1 year ago
0 votes
264 views

I know the ice maker is bad on this unit, the question I have is, I know these units used to be bad about icing up at the back of the air chute from freezer, causing condensation the freezing over. Do you know what the kit part number is for the updated foam seals and the rest of the kit?

0 votes
249 views

the top rack left front mount that goes into the rail is broken. we need to know how to replace

  • burtyost asked 1 year ago
  • last active 1 year ago
0 votes
544 views

Already replaced the temperature sensors but one thing we noticed was that oven was slightly warm without any use. Replaced the temperature sensors on both upper and lower oven but the customer called back saying it’s doing it again after like two months I’m starting to suspect it’s the control board?

0 votes
363 views

I can’t figure out how to access the refrigerator evaporator, need a service manual.

  • user asked 2 years ago
  • last active 2 years ago
0 votes
305 views

The refrigerator side is not keeping cool enough. The door just falls open and appears to have no suction. Normally on this unit the interior wall is warm but it is not warm on this one.

0 votes
571 views

do you have a video on removing the ice maker

  • burtyost asked 2 years ago
  • last active 2 years ago
1 vote
328 views

motor dose not stay on for full agitation for cleaning dishes or dissolve detergent.

  • rfcorral asked 2 years ago
  • last active 2 years ago
1 vote
343 views

how to force harvest on flex icemaker

  • Guest asked 2 years ago
  • last active 2 years ago
0 votes
687 views

Kitchen aide Bottom freezer. French doors. The refrigerator is cooling properly, but the freezer is not getting colder than 70 degrees. This is a dual evaporator model. We tried running diagnostics but could only get to step 4. Do you have more information on how to test this model. We are suspecting that the freezer evaporator switching valve may have an issue Is there a test to check this?

0 votes
456 views

KITCHENAID MICROWAVE RAN DIAGNOSTICS ERROR F1 E5 SCREEN SAYS REPLACE MICROWAVE INVERTER. I REPLACED INVERTER AND MICROWAVE CONTINUES TO GIVE SAME ERROR CODE. I CHECKED SOME OTHER POSTS AND THEY INDICATED THAT HE APPLIANCE MANAGER IS THE CULPRIT. I REPLACED THE APPLIANCE MANAGER DIAGNOSTICS SAYS STILL SAME ISSUE F1 E5 CAN YOU TELL ME WHERE TO GO FROM HERE. I TRIED TO RESET ERROR BY GOING INTO DIAGNOSTICS OFF OFF START THEN 6 THEN 6 AGAIN THEN PUSH START AND THAT IS SUPPOSED TO RESET BUT ONLY BEEPS.
WHAT OTHER CHECKS CAN I DO.

0 votes
439 views

KitchenAid refrigerator not cooling in fresh food section. Looks like it’s a defrost issue as freezer back wall is frosted up. Looking for tech assist on how to force it to defrost, etc. Also, what are the parts for desfrosting other than heater? Curious what this fridge has for defrost, ie sensor, thermistor, etc.

0 votes
669 views

Above items not working. Are they connected. Circuit wise? Please help with troubleshooting. Put it into diagnostic mode and it shows up with replace filter sign on first step. When I advance it to next step, it says order filter. When I check filter, it says it’s hundred percent. It’s been a big mystery. Thank you.

0 votes
404 views

Customer called for service on his icemaker…. after replacing the water valve to no avail, I found that the compartment in the ceiling with the icemaker and fan assembly was around 25-28°F, which I knew was too warm for the icemaker to operate. Yet, the bottom freezer compartment is well cold enough, in the single digits (2-5°F).

  • A.P.S. Co. asked 2 years ago
  • last active 2 years ago
1 vote
2k views

Ref is not cooling, no lights in the fresh food compartment and has a PF code. Previous tech replaced control board and user interface and still the same.

0 votes
548 views

My Kitchenaid DW will not cycle. The control panel lights up, but I cannot get the Start/Resume button to stop blinking. I think there may be an issue with the latch. The model is KUDP02FRWH3…it is pretty old, about 20 years.

0 votes
317 views

My KitchenAid dishwasher has an intermittent problem. Sometimes the buttons will not respond. If I flip the circuit breaker for the dishwasher the buttons come back on. This happens 2-3 times a week, then won’t for ~3 weeks, then happens again. Otherwise operation is fine.

0 votes
409 views

Trying to find out how to disassemble the bottom crisper to get to the dual water valve.

  • gsusrod asked 2 years ago
  • last active 2 years ago
0 votes
431 views
  • halco1242 asked 2 years ago
  • last active 2 years ago
0 votes
442 views
Showing 1 - 30 of 331 results