Brand: KitchenAid

there is a clicking sound from ALL the burners Evan when we dont try to light them
they do not ignite

This unit needs the 2 right infinite switches replaced. You can no longer get just one switch, you have to buy a switch kit with a wiring harness included. I have the part needed W10307362, but it came with no instructions at all. Can you get me the installation instructions? A video of this would be great if you have one available.

Tested element, reads good. Replaced control panel and main relay still no go? Tested heater connection on relay so means thermal fuse and wiring is fine, outlet a good 123v..? Goes through normal hour cycle but doesn’t dry..
Already asked question got French trouble shooting guide asking again

no water or ice disp and light

Preheating is taking 45min to reach 500f. For top oven only. Elements are fine, boards and temp probe have been replaced. Please help

Hello,

I have a KitchenAid Wall Microwave/Oven combo. Recently the the turntable stopped spinning. I checked the coupler and determined that it is not broken and suspect the issue is with the turntable motor (the turntable now spins freely, I don’t remember it doing that before). I need to know how to access the underside of the microwave (at least I think I need to) in order to replace the turntable. I’ve looked online and can’t find any videos or instruction on how to do this. Can you please help me with this issue or provide direction to reference materials to complete this task?

Thank you,
Jeff Wessling

I went out on this unit, the main PCB was making a clicking noise and not cold at all. The PCB is no longer available, so I sent it in for repair. I got it back and found that the compressor inverter was bad. I replaced the inverter. I thought that every thing was good but come to find out that the temperature in refrigerator was good but freezer only at 14 degrees when set to zero. it will not get colder. I replaced thermistor. Is there any way to calibrate. Thanks Ricky.

Frost buildup bottom refrigerator behind the food drawer please help

Light issues in freezer it stays stuck when door opens and the light assembly has been changed twice any advice.?

I have a kitchen aide refrigerator, the compressor and condenser fan is not working.

Ref is not cooling, no lights in the fresh food compartment and has a PF code. Previous tech replaced control board and user interface and still the same.

Is it normal for the upper oven to heat up 15 min longer than the lower? If not what can repair it?

i changed the igniter i changed the gas valve and nothing seems to correct the issue.
the igniter will not glow .

Unit powers on without issue. I had set the timer on the touchpad (for testing purposes) by pressing 1 0 0 0 ( for ten minutes ) and then hit “start”. After I hit the START button on the touchpad, the timer was counting down without issue but the microwave was not on or activated. I could not hear the motor or the fan or magnetron or anything.
Could there be a bad switch on the board inside ?

the stove top sparks are not working I did not hear anything at any burner that I try.
I will light only with a match

complaint, only portions of numbers light up. Oven works ok. If you set it for 325F , part of the 3 & 2 is not lite up. Whats going on?? Is this some type of error code??

Freezer is not making ice. We have replaced the ice maker, ice level boards and auger motor. Ran everything threw manual harvest and it filled with water, heater came on on icemaker and in the full tube. The temperature is set to -2. We have 14.7 volts to the optic boards. 120v to the icemaker. It has dumped ice 1 time on its own since everything was replaced 3 weeks ago. Both door switches are good and both are making good contact when the door is closed. Am I missing something? Is there anything else it could possibly be? Maybe a bad icemaker from factory not common but possible. And I do have the tech sheet, I have been threw it 3 or 4 times. Please email me back at. bryan@drappliances.com

I’m having an error 7-1 and 6-2. I need to know what these codes mean. Please help

how to force harvest on flex icemaker

motor dose not stay on for full agitation for cleaning dishes or dissolve detergent.

I never worked on this refrigerator before. I saw that the display board inside the ref. section had no power to it and when you press the power bottom it flashes and turns off and flashes every 20 seconds. Besides that board is there any other issues I should be aware. Please help

Kitchenaid rfg