Brand: KitchenAid

I removed the old thermistor and measured the resistance in a glass of ice water and got 4.99 omes. I then took the new thermistor and put it in ice water and got 6.3 oms. My question is with the difference of 10 omes is the old thermistor still good.

I’ve had a job numerous times And they keep referring them to Warrantee because I’m assuming if the fuel system issue but I followed up with several of these customers and they said warranty he came out and fixed it in like 10-15 minutes. I have the job again and I’m wondering what the guys from warranty did there must be a service bulletin out for this basically build up a snow blocks only underneath where the fan is located on the evaporator you guys answer this question before that it might be deprived evaporator But how could they be fixed in 10 to 15 minutes? Please don’t link videos or diagnostic stuff unless it addresses this exact issue with this freezer fan.

Have an odd one here. display on touch pad goes dead after a few weeks. unplug unit and it restores normal operation, been out 2 times and unplugged and came back on. I don’t want to just throw parts at this, anyone see this before or have any suggestions. Thanks in advance

Dishwasher rack is uneven, Rack falls out

Where can I find the part numbers for the water lines going from the water inlet valve to dispenser and icemaker ? Both are cracked at the 90 degree elbow at the valve. I have a picture of the end at the water valve but don’t know how to upload on here if its even possible.

Looks like the ice maker is shot, any one there have the part information readily available?

Error F6 E0, Food is cooked unevenly.

followed the video byt when I got to the fuse portion, I have power on both leads,, what next?

I have a KitchenAid dishwasher.
This unit when the customer uses a heated wash or dry condensates from the water inlet on the left side of tub. The insulation blanket on the unit has a 12″ circular mold spot and the cabinet has the same size water spot. The flap in the inlet is fine. It is pretty tight in the cabinet. The unit is about 11 months old the home is also new.
The customer saw the water mark on the cabinet under the sink.
Any advice on this one sure would be appreciated.

Above items not working. Are they connected. Circuit wise? Please help with troubleshooting. Put it into diagnostic mode and it shows up with replace filter sign on first step. When I advance it to next step, it says order filter. When I check filter, it says it’s hundred percent. It’s been a big mystery. Thank you.

I CHECKED OUT THE REFRIGERATOR AND THE EVAPORATOR FAN HAS POWER, BUT IS NOT WORKING. I NOTICED THAT THERE IS A LARGE BLOCK OF ICE ABOVE THE RIGHT SIDE OF THE COIL, NOT ON THE COIL. THE COIL DID HAVE SOME UNEVEN FROSTING. THIS REFRIGERATOR IS KEPT OUTSIDE AND THE NIGHT BEFORE I CHECKED IT THE TEMP OUTSIDE DROPPED DOWN. THE BLOCK OF ICE IS NOT BLOCKING THE AIR DUCT, SO IF I REPLACE THE FAN IT SHOULD FIX THE FRIDGE TEMP PROBLEM, BUT I AM CONCERNED WITH THE ICE BLOCK AND UNEVEN PATTERN ON THE COIL. I WOULD LOVE TO PUT IT IN MANUAL DEFROST, BUT I DID NOT KNOW HOW. I TOLD THE CUSTOMER TO EMTY THE FREZZER AND LET IT DEFROST. WHEN I GO BACK WHAT SHOULD I CHECK? THANKS, TODD FROM NY.

Thought maybe old fan was working intermittent so I replaced it and lubricated the gaskets but two weeks later snow is back and getting into the fan and cooling poorly. Rest of the coils are nice and frosty so clearly sealed system is ok. Fridge is like 5 years old. The metal defrost thermistor?

My ice maker is not making cubes. How can I check to see if it’s getting water?

I replaced the touchpad panel about 2 weeks ago and now it is acting up. It finished a cycle and the clean light came on but two other LEDs came on faintly and are now constantly on…….nothing can make them go out .

The LEDs are for the “Potscrub” and “Heat Dry” if that helps any.

I hope the panel isn’t toast already and if so WHY??

The dishwasher blue light will come on like it is going to start the cycle. I hear no noise and then the blue light goes off. when I open it, the cancel, drain light is on.

Everything else works but the compressor and condenser fan. The tech sheet is missing. Is it the control board or what?

My Kitchenaid fridge’s control panel won’t turn on. If I press the On/Off button, it flickers briefly, but then goes out again.

clips screws what do i need to make this job an easy quick deal//?

Question on this range .The complaint is the temperature doesn’t rise above 180 degrees.
Technician came out he found in both bake and broil cycle part is on
the electric element just below the broiler burner . We are not familiar with this type of range. We will really appreciate any input.