Brand: LG

this LG top load washer goes off balance almost every load. not loading or doing anything different than I did in the past. started doing this 2 months ago. Is it the balance ring, suspension rods, need software update, or combination of all? I can hear water in the balance ring, has some of it leaked out? Bearings and tub are in good condition. tub nut is not loose and bearings are not worn or loud. machine is level and firm on the floor. I have read this is a very common problem with LG top loaders. Select Normal cycle, fills, agitates, then after a few minutes starts spinning in one direction with clothes and water, tub starts banging against side of washer. Then it stops and reverses direction, spinning with clothes and water, bang, bang, bang, stops and goes back to agitating. The machine will do this with no clothes in it, on the normal cycle.

The evaporator coils on this unit were so frozen up they busted the fan and fan housing. I have everything defrosted off, checked the heater but not sure what the resistance should be. Do you guys have lots of trouble with the boards on these, or is this more than likely the defrost sensor?

Phoned lg trying to find out about this board. LG said they are the only one who can sell and install this board. Is there any way around this. Number of board is EBR38163323. Model no. is nowhere to be found online yet when I phoned LG they said it is a good model no. Model no. is wm2233cs.

Rattling and buzzing sounds during drain.

The refrigerator is not cooling at all but the fans are working could you help me out with this. Thank you

Lg washer how do you reinstall spring and locker hook and pin on inner door panel? I cannot figure how to put the spring back on.

I have an LMXS30776S/00 LG refrigerator with no cooling whatsoever. Refrigerator has never been used. No heat felt on compressor. Resistance across C & P terminals of compressor is 8.2 ohms. All sensors in freezer and refrigerator check out good. Smart diagnosis comes up with no data. When i test PCB, I get a 3 blink code on LED. Tapped high and low side and pressure remains the same with and without power. Is my compressor bad or PCB? Voltage gets up to 13V0AC before it times out.

I did some research and found a lot of different options… Oh by the way, I hate LG products, and I’ll never work on another one.

Do you guys have a video for this? Having a really hard time with it.

Pretty sure it’s the evaporator fan motor but can’t find any information on it. Hoping you have it there.

The bottom freezer door on my LG refrigerator is stuck shut.

My dryer is displaying error code.

Also, what does this mean?

My LG washer is giving off a burning smell.

Hello, I am working on a L.G. French door refrigerator. Condesor fan runs. Compressor does not start. The controller board that operates the compressor has a green light that flashes. I feel the control board is bad, my question is could a thermistor or any other input cause this situation.

WHERE CAN I FIND A SUBSTITUTE FOR THIS THERMISTOR / OVERLOAD RELAY
PART # EBG44336401
CAN I USE A DIFFERENT RELAY SAY FROM A WHIRLPOOL AND JUST CHANGE THE PLUG IN WIRES TO A SMALLER SIZE?

No tech sheet I can find, what am I looking at in terms of parts to correct this? Runs for a few minutes, then quits and errors out.

We have an LG dryer that is not igniting. We are getting power down to the ignitor and a good amp draw from the ignitor.
So far we have completed :
1) Replaced the ignitor and the gas valve will still not open. Ignitor has a strong glow and proper amp draw.
2) Replaced the gas valve that has the coils built in to the valve.
3) Checked for proper gas pressure up to the gas valve, the customer happens to work for the gas company.

Is there any service bulletin or recall on this unit ? I am leaning towards the main control board but would greatly appreciate any input before replacing the board. Any input is greatly appreciated.

    Sometimes after using the breach dispenser, the dispenser is full of water and maybe breach? That is the customers complain. Is there a part to replace? Any advice would be helpful. Thanks Ricky

The part I was given to replace was part # AJU72992601 and to me it looks different it has water in and water out and a coil with the block connector but it also has a wire connector coming from another control part ebd60664501. I’m woundering where those wires would go. I’m not at the unit now and was looking for a video to show me

Seems to be cycling correctly per the customer but not getting detergent in. Any thoughts?

I’m almost positive this is a water valve but can’t find the schematic breakdown, anyone there have a minute to look it up for me? Thanks.